RADIATOR (w/o DPF) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Cold Area Specification Vehicles)

    Note


    • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE UPPER RADIATOR SUPPORT SEAL


    1. Remove the 13 clips and upper radiator support seal.

  3. REMOVE FRONT BUMPER LOWER COVER


    1. Remove the clip, 5 bolts and front bumper lower cover.

  4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. Remove the 4 bolts and No. 1 engine under cover.

  5. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. A00JWDE

      Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

    3. Loosen the cylinder block drain cock plug.

      A00JVX9E01
      Text in Illustration
      *1 Radiator Reservoir *2 Vent Plug
      *3 Radiator Drain Cock Plug *4 Cylinder Block Drain Cock Plug

  6. REMOVE FRONT BUMPER COVER


    1. Remove the front bumper cover Click here.

  7. REMOVE FRONT BUMPER UPPER RETAINER


    1. A00K0S1

      Remove the 3 bolts and retainer.

  8. REMOVE RADIATOR SIDE DEFLECTOR RH


    1. A00JVV1

      Using a clip remover, detach the 3 claws and remove the clip. Then move the side deflector so that the radiator can be removed in the step below.

  9. REMOVE RADIATOR SIDE DEFLECTOR LH


    1. A00K1EQ

      Using a clip remover, detach the 3 claws and remove the clip. Then move the side deflector so that the radiator can be removed in the step below.

  10. REMOVE NO. 1 AIR HOSE


    1. A00OADW

      Loosen the 2 clamps.

    2. Remove the No. 1 air hose from the inlet pipe and intercooler.

  11. REMOVE INTERCOOLER AIR HOSE


    1. A00O34C

      Disconnect the No. 2 vacuum transmitting hose from the intercooler.

    2. A00OBD1

      Loosen the 2 clamps.

    3. Remove the intercooler hose from the intake pipe and intercooler.

  12. REMOVE NO. 1 RADIATOR HOSE

    A00O4GN

  13. REMOVE NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)


    1. A00O74S

      Remove the 2 nuts from the battery terminal.

    2. Detach the 3 wire harness clamps.

    3. Remove the No. 3 engine wire from the fan shroud.

  14. REMOVE FAN SHROUD


    1. A00O3CJ

      Disconnect the No. 1 water by-pass hose and detach the 2 clamps from the fan shroud.

    2. Disconnect the No. 2 water by-pass hose from the radiator reservoir.

    3. Remove the 3 bolts and radiator reservoir.

    4. for Automatic Transmission:


      1. Remove the inlet and outlet oil cooler hoses and detach the clamp from the fan shroud.

      2. A00O6YT

        Disconnect the 2 oil cooler hoses from the radiator.

    5. A00O5ZQ

      Loosen the 4 nuts holding the fluid coupling and fan.

    6. Remove the fan and generator V belt Click here.

    7. A00O6LU

      Remove the 2 bolts holding the fan shroud.

    8. Remove the 4 nuts for the fan with fluid coupling fan, and then remove the shroud together with the coupling fan.

      Note

      Be careful not to damage the radiator core.

    9. Detach the No. 2 water by-pass hose from the hose clamp on the fan shroud.

    10. A00O6JL

      Remove the No. 2 water by-pass hose from the water inlet.

    11. Remove the fan pulley from the water pump.

  15. DISCONNECT NO. 2 RADIATOR HOSE

    A00JZEL

  16. REMOVE RADIATOR ASSEMBLY WITH INTERCOOLER ASSEMBLY


    1. A00K0WJ

      Remove the 4 bolts and radiator with intercooler.

    2. A00JXCB

      Remove the 2 No. 1 radiator support seals from the radiator.

  17. REMOVE NO. 1 RADIATOR AIR GUIDE


    1. A00JZP9

      Remove the 2 bolts and the radiator air guide.

    2. A00JZZ3

      Remove the No. 3 radiator support seal from the radiator air guide.

  18. REMOVE NO. 2 RADIATOR TO SUPPORT SEAL


    1. A00K120

      Remove the 2 No. 2 radiator to support seals from the intercooler.

  19. REMOVE INTERCOOLER ASSEMBLY


    1. A00JW32

      Disconnect the vacuum hose from the intercooler.

    2. Remove the 4 bolts and intercooler from the radiator.

  20. REMOVE VACUUM TRANSMITTING PIPE SUB-ASSEMBLY


    1. A00JWOC

      Detach the 2 clamps and remove the vacuum transmitting pipe from the radiator.

  21. REMOVE NO. 1 RADIATOR SUPPORT


    1. Remove the 2 radiator supports.

  22. REMOVE NO. 2 RADIATOR SUPPORT


    1. Remove the 2 radiator supports.

  23. REMOVE NO. 1 RADIATOR SUPPORT BUSH


    1. Remove the 4 radiator support bushes.