EXHAUST FUEL ADDITION INJECTOR INSTALLATION


  1. INSTALL FUEL INJECTOR SEAL


    1. Install a new E-ring, O-ring and 3 backup rings to the exhaust fuel addition injector.

      A00JXG9E01
      Text in Illustration
      *A Alignment Opening - -
      *1 O-Ring *2 E-Ring
      *3 No. 1 Backup Ring *4 No. 2 Backup Ring
      *5 No. 3 Backup Ring - -
      *a Incorrect *b Correct
      *c Overlapped *d Normal
      *e Stretched - -

      Note


      • Check that there is no foreign matter or damaged areas in the injector O-ring groove.

      • Check that the No. 1 and No. 2 backup rings are installed in the correct direction.

      • Make sure that the backup rings and O-ring are installed in the correct order.

      • Check that the alignment openings of the backup rings are not overlapped or stretched as shown in the illustration.

      • After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.

  2. INSTALL EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

    Note

    If there is foreign matter on the installation surface of the exhaust fuel addition injector, be sure to clean it before installation.


    1. Install a new gasket and the exhaust fuel addition injector.

    2. Using a T40 "TORX" socket wrench, install the No. 1 nozzle holder clamp with the screw.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    3. Install the injector holder with the 2 bolts.

      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  3. INSTALL TURBINE OUTLET ELBOW

    Click here

  4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. ADD ENGINE COOLANT


    1. Tighten the radiator drain cock plug by hand.

    2. Tighten the cylinder block drain cock plug.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the reservoir tank.

      Standard Capacity
      Item Specified Condition
      for Automatic Transmission w/ Rear Heater 14.9 liters (15.7 US qts, 13.1 Imp. qts)
      w/o Rear Heater 13.1 liters (13.8 US qts, 11.5 Imp. qts)
      for Manual Transmission w/ Rear Heater 15.0 liters (15.8 US qts, 13.2 Imp. qts)
      w/o Rear Heater 13.2 liters (13.9 US qts, 11.6 Imp. qts)

      Tech Tips


      • TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

      • Please contact your TOYOTA dealer for further details.

      • for Cold Area Specification Vehicles:

        Please contact any authorized TOYOTA dealer or repairer or another duly qualified and equipped professional for further details.

      Note

      Never use water as a substitute for engine coolant.

    4. Press the No. 1 and No. 2 inlet and No. 1 and No. 2 outlet radiator hoses several times by hand, and then check the level of the coolant.

      If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

    5. Install the radiator reservoir cap.

    6. Using a wrench, install the vent plug.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

    7. Bleed air from the cooling system.


      1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      2. Maintain the engine speed at a speed between 2500 and 3000 rpm.

      3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

        CAUTION:

        When pressing the radiator hoses:


        • Wear protective gloves.

        • Be careful as the radiator hoses are hot.

        • Keep your hands away from the radiator fan.

      4. Stop the engine and wait until the coolant cools down to ambient temperature.

        CAUTION:

        Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    8. After the coolant cools down, check that the coolant level is at the FULL line.

      If the coolant level is below the FULL line, add TOYOTA SLLC to the FULL line.

  6. INSPECT FOR ENGINE COOLANT LEAK

    Note

    Before each inspection, turn the A/C switch off.

    CAUTION:

    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Fill the radiator with coolant and attach a radiator cap tester.

    2. Warm up the engine.

    3. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.

      If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.

  7. INSPECT FOR FUEL LEAK


    1. Perform the Active Test.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

      5. Perform the Active Test.

        Intelligent Tester Display Test Part Control Range Diagnostic Note
        Test the Fuel Leak Pressurize common rail interior and check for fuel leaks Stop/Start

        • The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.

        • The above conditions are maintained while the Active Test is being performed.

  8. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. Install the No. 1 engine under cover with the 4 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }