REAR DOOR WINDOW FRAME MOULDING REMOVAL

  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

    1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

      A011SXD

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

      A011R4A

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE REAR ARMREST ASSEMBLY

    1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

      A011VBG

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    1. Put protective tape around the rear door panel.

      A011S38E01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 3 screws.

      A011U67

    3. Using a clip remover, disengage the 8 clips.

    4. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

      A011UCCE01
      Text in Illustration
      *1 Reference Boss
      *2 Rear Door Inner Glass Weatherstrip

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

      A011UFW

    8. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

      A011TZFE01
      Text in Illustration
      *1 Screwdriver

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

    1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

      A011TBLE01
      Text in Illustration
      *1 Screwdriver

  8. REMOVE REAR DOOR SERVICE HOLE COVER

    1. Disconnect the connector and remove the rear door service hole cover.

      A011SGK

      Tech Tips

      Remove any remaining butyl tape from the door.

  9. REMOVE REAR DOOR CHECK ASSEMBLY

    1. Remove the bolt and 2 nuts, and rear door check assembly.

      A011SXY

  10. REMOVE REAR DOOR WEATHERSTRIP

    1. Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.

      A011R57

  11. REMOVE REAR DOOR GLASS RUN

    1. Remove the rear door glass run.

      A011UWH

  12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

    1. Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      A011V10

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  13. REMOVE REAR DOOR QUARTER WINDOW GLASS

    1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

      A011V1M

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      A011R7S

      Note

      Do not damage the door glass.

  15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

    1. Put protective tape around the rear door belt moulding assembly.

      A011VBHE01
      Text in Illustration
      *1 Protective Tape

    2. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.

      A011SZZE01
      Text in Illustration
      *1 Protective Tape

      Tech Tips

      Tape the screwdriver tip before use.

  16. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

    Tech Tips

    When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or moulding excessively.

    1. Using a heat light, heat the rear door front window frame moulding.

    2. Using a moulding remover, disengage the clip and remove the rear door front window frame moulding.

      A011SSQE01
      Text in Illustration
      *1 Double-sided Tape
      *2 Caulking Sponge

  17. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    2. Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      A011R87E01
      Area Dimension
      A 5.0 mm

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

      Note

      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

      • Be careful of the drilled rivets, as they may be hot.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

    5. Disengage the guide, remove the rear door upper window frame moulding from the door frame.