FUEL LID LOCK CONTROL CABLE ASSEMBLY REMOVAL

  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Manual Seat)

    Click here

  4. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Power Seat)

    Click here

  5. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Manual Seat)

    Click here

  6. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Power Seat)

    Click here

  7. REMOVE REAR SEAT CUSHION ASSEMBLY

    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.

      1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        A011UEME01
        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  8. REMOVE REAR SEAT CUSHION LOCK HOOK

    1. Disengage the claw and remove the rear seat cushion lock hook.

      A011RZN

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. Remove the 2 bolts.

      A011R15

    4. Disengage the hook and remove the rear side seatback assembly LH.

  10. REMOVE FRONT DOOR SCUFF PLATE LH

    1. Disengage the 10 claws and remove the front door scuff plate LH.

      A011RIY

  11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    1. Disconnect the front door opening trim weatherstrip.

  12. REMOVE REAR DOOR SCUFF PLATE LH

    1. Disengage the 6 claws and remove the rear door scuff plate LH.

      A011RO9

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

    1. Disconnect the rear door opening trim weatherstrip.

  14. REMOVE LAP BELT OUTER ANCHOR COVER

    1. Disengage the 3 claws and remove the lap belt outer anchor cover.

      A011UT6

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

      A011STL

  16. REMOVE CENTER PILLAR LOWER GARNISH LH

    1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

      A011T7N

  17. REMOVE LUGGAGE COMPARTMENT DOOR COVER

    1. Remove the 13 clips and luggage compartment door cover.

      A011TF6

  18. REMOVE SPARE WHEEL COVER ASSEMBLY

    1. Remove the spare wheel cover assembly.

  19. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)

    1. Remove the baggage holder net.

  20. REMOVE REAR FLOOR FINISH PLATE

    1. Remove the 5 clips.

      A011SS8

    2. Disengage the 4 clips and remove the rear floor finish plate.

      A011R0B

  21. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    1. Push the pin and remove the No. 1 luggage compartment trim hook.

      A011RV9E01
      Text in Illustration
      *1 Pin

  22. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH

    1. Remove the clip <A>.

      A011R32E01
      Text in Illustration
      *1 Clip <A>
      *2 Clip <B>

    2. Remove the 2 clips <B>.

    3. Disengage the fastener and remove the luggage compartment inner trim cover LH.

      A011RSV

  23. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

    1. Remove the screw.

      A011ROE

    2. Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

      A011TLD

    3. Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

      A011S9B

  24. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

    1. Disengage the 2 clamps.

      A011RO4

    2. Using a clip remover, disengage the clamp and disconnect the wire harness.

      A011R0X

    3. Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

      A011TCL

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. w/o Wireless Door Lock Control System:

      1. Disconnect the luggage door lock control cable sub-assembly.

        A011RX0

      2. Disengage the 3 clamps and disconnect the luggage door lock control cable sub-assembly.

        A011RQB

    6. w/ Wireless Door Lock Control System:

      1. Disengage the guide as shown in the illustration.

        A011TN1

      2. Disconnect the luggage door lock control cable sub-assembly.

        A011SWN

      3. Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

        A011RTY

    7. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.

      A011SHDE01
      Text in Illustration
      *1 Cutout
      *2 Guide <A>

    8. Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.

      A011TFTE01
      Text in Illustration
      *1 Cutout
      *2 Guide <B>

    9. Pull out the fuel filler opening lid lock retainer with both guides <B and C> aligned with the cutouts.

      A011RZ9E01
      Text in Illustration
      *1 Cutout
      *2 Guide <C>
      *3 Guide <B>

    10. Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

      A011T8S

    11. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      A011S5ZE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    12. Using a knife, cut off the clamp as shown in the illustration.

      A011UYCE01
      Text in Illustration
      *1 Tape - -
      *a Cut - -

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    13. Remove the clamp.

    14. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.