SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tech Tips

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.

    5. Read the Data List according to the display on the Techstream.

      Sliding Roof
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Open Switch OPEN switch signal/ON or OFF

      ON: OPEN switch pressed

      OFF: OPEN switch not pressed

      		 -
      Close Switch CLOSE switch signal/ON or OFF

      ON: CLOSE switch pressed

      OFF: CLOSE switch not pressed

      		 -
      Up Switch UP switch signal/ON or OFF

      ON: UP switch pressed

      OFF: UP switch not pressed

      		 -
      Down Switch DOWN switch signal/ON or OFF

      ON: DOWN switch pressed

      OFF: DOWN switch not pressed

      		 -
      Front SW Auto Operation Sliding roof auto function/ON or OFF Customization status displayed -
      Hall IC1 Pulse Hall IC1 pulse output/Lo or Hi Lo and Hi repeat during motor operation

      Lo: Hall IC1 output is low

      Hi: Hall IC1 output is high
      Hall IC1 Status Status of Hall IC1/Normal or Error

      Normal: Hall IC1 normal

      Error: Hall IC1 not normal

      		 -
      Hall IC2 Pulse Hall IC2 pulse output/Lo or Hi Lo and Hi repeat during motor operation

      Lo: Hall IC2 output is low

      Hi: Hall IC2 output is high
      Hall IC2 Status Status of Hall IC2/Normal or Error

      Normal: Hall IC2 normal

      Error: Hall IC2 not normal

      		 -
      Ignition (Direct Signal) Ignition switch signal/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 -
      Ignition (MPX) Ignition switch signal (LIN signal)/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 -
      Door Courtesy Driver door courtesy light switch signal/ON or OFF

      ON: Driver door open

      OFF: Driver door closed

      		 -
      Door Key Close Operation Key-linked sliding roof close signal/ON or OFF

      ON: Turn and hold the driver door key cylinder to lock position

      OFF: Driver door key cylinder not turned

      		 -
      Door Key Open Operation Key-linked sliding roof open signal/ON or OFF

      ON: Turn and hold the driver door key cylinder to unlock position

      OFF: Driver door key cylinder not turned

      		 -
      Wireless Open Operation*1 Wireless transmitter-linked sliding roof open signal/ON or OFF

      ON: Press and hold the transmitter UNLOCK switch

      OFF: Transmitter UNLOCK switch not pressed

      		 -
      Key Off Permission Key-off sliding roof operation permit signal/ON or OFF

      ON: Front doors are not opened within 43 seconds after ignition switch turned off

      OFF: Any status except "ON" status

      		 -
      Door Key Related Operation Key-linked sliding roof open function operating direction/Slide or Tilt Customization status displayed -
      Wireless Key Rel Operation*1 Wireless transmitter-linked sliding roof open function operating direction/Slide or Tilt Customization status displayed -
      Open Switch Failure(Past) Open switch failure signal (Past)/ON or OFF

      ON: Sliding roof open switch failure signal (Past)

      OFF: No sliding roof open switch failure signal (Past)

      		 -
      Close Switch Failure(Past) Close switch failure signal (Past)/ON or OFF

      ON: Sliding roof close switch failure signal (Past)

      OFF: No sliding roof close switch failure signal (Past)

      		 -
      Up Switch Failure(Past) Up switch failure signal (Past)/ON or OFF

      ON: Sliding roof tilt up switch failure signal (Past)

      OFF: No sliding roof tilt up switch failure signal (Past)

      		 -
      Down Switch Failure(Past) Down switch failure signal (Past)/ON or OFF

      ON: Sliding roof tilt down switch failure signal (Past)

      OFF: No sliding roof tilt down switch failure signal (Past)

      		 -
      Open Switch Failure(Current) Open switch failure signal (Current)/ON or OFF

      ON: Sliding roof open switch failure signal (Current)

      OFF: No sliding roof open switch failure signal (Current)

      		 -
      Close Switch Failure(Current) Close switch failure signal (Current)/ON or OFF

      ON: Sliding roof close switch failure signal (Current)

      OFF: No sliding roof close switch failure signal (Current)

      		 -
      Up Switch Failure(Current) Up switch failure signal (Current)/ON or OFF

      ON: Sliding roof tilt up switch failure signal (Current)

      OFF: No sliding roof tilt up switch failure signal (Current)

      		 -
      Down Switch Failure(Current) Down switch failure signal (Current)/ON or OFF

      ON: Sliding roof tilt down switch failure signal (Current)

      OFF: No sliding roof tilt down switch failure signal (Current)

      		 -
      Number of Trouble Codes Number of DTCs / Min.: 0, Max.: 255 Number of stored DTCs -
      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Door Key P/W Up Door key linked sliding roof close/ON or OFF Customization status displayed -
      Door Key P/W Down Door key linked sliding roof open/ON or OFF Customization status displayed -
      P/W Down W/Transmit*1 Wireless transmitter linked sliding roof open/ON or OFF Customization status displayed -
      Slide Roof Open Warning Sliding roof open warning/ON or OFF Customization status displayed -

      • *1: w/ Daytime Running Light Control

  2. ACTIVE TEST

    Tech Tips

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Active Test.

    5. Perform the Active Test according to the display on the Techstream.

      Sliding Roof
      Tester Display Test Part Control Range Diagnostic Note
      Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -