ROOF HEADLINING REMOVAL

  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE LH

    1. Disengage the 10 claws and remove the front door scuff plate LH.

      A011RIY

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

    1. Remove the clip.

      A011S09

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    1. Remove the front door opening trim weatherstrip LH.

  6. REMOVE FRONT PILLAR GARNISH LH

    1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      A011UOZE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

      A011S2ME01

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. Protect the curtain shield airbag assembly.

      A011THME01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  7. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  11. REMOVE REAR SEAT CUSHION ASSEMBLY

    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.

      1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        A011UEME01
        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  12. REMOVE REAR SEAT CUSHION LOCK HOOK

    1. Disengage the claw and remove the rear seat cushion lock hook.

      A011RZN

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  13. REMOVE INNER LUGGAGE COMPARTMENT TRIM PAD

    1. Remove the inner luggage compartment trim pad.

      A011UK0

  14. REMOVE REAR SEATBACK ASSEMBLY RH

    1. Disengage the 3 fasteners as shown in the illustration.

      A011RKUE01
      Text in Illustration
      *1 Fastener

    2. Remove the 2 bolts and rear seatback assembly RH.

      A011USQ

      Note

      Be careful not to damage the vehicle body.

  15. REMOVE REAR SEATBACK ASSEMBLY LH

    1. Disengage the 2 fasteners as shown in the illustration.

      A011QQXE01
      Text in Illustration
      *1 Fastener

    2. Remove the 2 bolts and rear seatback assembly LH.

      A011V0T

      Note

      Be careful not to damage the vehicle body.

  16. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. Remove the 2 bolts.

      A011TUN

    4. Disengage the hook and remove the rear side seatback assembly RH.

  17. REMOVE REAR SIDE SEATBACK ASSEMBLY LH

    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. Remove the 2 bolts.

      A011R15

    4. Disengage the hook and remove the rear side seatback assembly LH.

  18. REMOVE REAR DOOR SCUFF PLATE LH

    1. Disengage the 6 claws and remove the rear door scuff plate LH.

      A011RO9

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    1. Remove the rear door opening trim weatherstrip LH.

  20. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

    1. Disengage the 3 claws and remove the lap belt outer anchor cover.

      A011UT6

  21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

      A011STL

  22. REMOVE CENTER PILLAR LOWER GARNISH LH

    1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

      A011T7N

  23. REMOVE CENTER PILLAR UPPER GARNISH LH

    1. Remove the 2 screws.

      A011U1C

    2. Disengage the clip.

    3. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

  24. REMOVE ROOF SIDE INNER GARNISH LH

    1. Disengage the 5 clips.

      A011SLI

    2. Disengage the guide and remove the roof side inner garnish LH.

  25. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  27. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  29. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  30. REMOVE CENTER PILLAR UPPER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  31. REMOVE ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  32. REMOVE FRONT SEAT ASSEMBLY LH

    for TMMK Made Manual Seat Click here

    for TMMK Made Power Seat Click here

    for SIA Made Manual Seat Click here

    for SIA Made Power Seat Click here

  33. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  34. REMOVE INSTRUMENT PANEL ASSEMBLY

    Click here

  35. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    1. Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.

      A011QUV

    2. Disengage the 2 claws and remove the inner rear view mirror stay holder cover.

      A011UY3

  36. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

    1. Using a moulding remover, disengage the 4 clips.

      A011R6D

    2. Disconnect the connector and remove the roof console box assembly.

  37. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

    1. Using a moulding remover, disengage the 4 clips.

      A011ROC

    2. Disconnect the connector and remove the roof console box assembly.

  38. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.

      A011RO2E01
      Text in Illustration
      *1 Protective Tape
      *a Front

    2. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws as shown in the illustration and remove the No. 1 room light housing.

      A011REHE01
      Text in Illustration
      *1 Protective Tape
      *a Front

    3. Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.

      A011U29E02
      Text in Illustration
      *1 Room Light Switch Base

  39. REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 8 claws and remove the 2 spot light lenses.

      A011USAE01
      Text in Illustration
      *1 Protective Tape
      *a Front

    2. Using a screwdriver with its tip wrapped with protective tape and moulding remover, disengage the 2 claws <A>.

      A011USGE01
      Text in Illustration
      *1 Protective Tape
      *2 Claw <A>
      *3 Claw <B>
      *4 Claw <C>
      *a Front

    3. Disengage the 2 claws <B> and 2 claws <C>, and disconnect the spot light housing.

    4. Using a screwdriver, disengage the 8 claws and disconnect the 2 map light sub-assemblies from the spot light housing.

      A011RPXE01
      Text in Illustration
      *1 Map Light Sub-assembly

  40. REMOVE ASSIST GRIP SUB-ASSEMBLY

    1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      A011UQHE01
      Text in Illustration
      *1 Protective Tape

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disengage the 2 clips and remove the assist grip sub-assembly.

      A011R7Q

    3. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the RH side.

  41. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      A011SKZE01
      Text in Illustration
      *1 Protective Tape

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Disengage the 2 clips and remove the rear assist grip assembly LH.

      A011SNZ

    3. Remove the 2 clips from the vehicle body.

  42. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  43. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

    1. Remove the sliding roof opening trim moulding.

  44. REMOVE VISOR BRACKET COVER (for LH Side)

    1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

      A011SV3

  45. REMOVE VISOR ASSEMBLY LH

    1. Remove the 2 screws and visor assembly LH.

      A011SKM

  46. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  47. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  48. REMOVE VISOR HOLDER

    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

      A011UJLE01

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the other visor holder.

  49. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

    1. w/ EC Mirror

      1. Disconnect the connector from the inner rear view mirror.

    2. Remove the bolt and disconnect the bracket from the front pillar RH.

      A011TGNE01
      Text in Illustration
      *A w/o Satellite Radio *B w/ Satellite Radio

    3. Disengage the 3 clamps from the front pillar RH.

    4. Disengage the 4 clamps from the front pillar LH.

    5. w/o Satellite Radio:

      1. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

    6. w/ Satellite Radio:

      1. Disengage the 2 clamps and disconnect the 2 connectors from the rear pillar RH.

    7. Remove the 2 clips.

    8. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

      Tech Tips

      Leave the 2 clips in the vehicle.

    9. Remove the roof headlining assembly from the vehicle through the front door RH.

      A011TLH

      Note

      Do not damage the roof headlining assembly or body interior.

    10. Remove the 2 clips from the vehicle body as shown in the illustration.

      A011V4T

  50. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

    1. w/ EC Mirror

      1. Disconnect the connector from the inner rear view mirror.

    2. Disconnect the connector from the sliding roof drive gear assembly.

      A011SU7E01
      Text in Illustration
      *A w/o Satellite Radio *B w/ Satellite Radio

    3. Remove the bolt and disconnect the bracket from the front pillar RH.

    4. Disengage the 3 clamps from the front pillar RH.

    5. Disengage the 4 clamps from the front pillar LH.

    6. w/o Satellite Radio:

      1. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

    7. w/ Satellite Radio:

      1. Disengage the 2 clamps and disconnect the 2 connectors from the rear pillar RH.

    8. Remove the 2 clips.

    9. Disengage the 2 fasteners.

    10. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

      Tech Tips

      Leave the 2 clips in the vehicle.

    11. Remove the roof headlining assembly from the vehicle through the front door RH.

      A011V8W

      Note

      Do not damage the roof headlining assembly or body interior.

    12. Remove the 2 clips from the vehicle body as shown in the illustration.

      A011V4T