AIR CONDITIONING SYSTEM (for Manual Air Conditioning System), Diagnostic DTC:B1443

DTC Code DTC Name
B1443 Air Outlet Damper Control Servo Motor Circuit

DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (air outlet) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) to any position, which controls the air outlet switching.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

Tech Tips

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

DTC No. DTC Detection Condition Trouble Area
B1443 Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (air outlet)

  • No. 1 air conditioning radiator damper servo sub-assembly (air outlet)

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

WIRING DIAGRAM

A011TSVE32

INSPECTION PROCEDURE

PROCEDURE

  1. READ VALUE USING TECHSTREAM

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Operate the MODE switch.

    5. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    6. Check the value(s) by referring to the table below.

      Air Conditioner
      Tester Display Test Part Control Range Diagnostic Note
      Air Outlet Servo Actu Pulse(D)

      No. 1 air conditioning radiator damper servo sub-assembly (air outlet) actual pulse /

      Min.: 0

      Max.: 255

      FACE: 8 (pulse)

      B/L: 30 (pulse)

      FOOT (except MAX. HOT): 67 (pulse)

      FOOT (MAX. HOT): 74 (pulse)

      FOOT/DEF: 80 (pulse)

      DEF: 97 (pulse)

      		 -
      OK
      The display is as specified in the normal condition column.
      Result
      Result Proceed to
      NG A
      OK (When troubleshooting according to Problem Symptoms Table) B
      OK (When troubleshooting according to the DTC) C
    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET) Click here

    A

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  2. REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET)

    1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air outlet) Click here.

      Tech Tips

      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

    2. Check for the DTC.

      Result
      Result Proceed to
      DTC B1443 is output A
      DTC B1443 is not output B
    B

    END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY WAS DEFECTIVE)

    A

  3. REPLACE AIR CONDITIONING HARNESS ASSEMBLY

    1. Replace the air conditioning harness assembly Click here.

      Tech Tips

      Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.

    2. Check for the DTC.

      Result
      Result Proceed to
      DTC B1443 is output A
      DTC B1443 is not output B
    B

    END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

    A

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here