REAR SEAT INNER BELT ASSEMBLY INSTALLATION

  1. INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

    1. Before installing the rear seat inner with center belt assembly LH, check the ELR function.

      A011R0PE01

      Note

      Do not disassemble the retractor.

      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        Text in Illustration
        *1 Retractor
        *a Unlocked
        *b Locked
        *c 45°

        If the result is not as specified, replace the rear seat inner with center belt assembly LH.

  2. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

    1. Engage the guide to temporarily install the rear seat inner with center belt assembly LH.

    2. Install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. Check if the ELR locks.

      Note

      The check should be performed with the rear seat inner with center belt assembly LH installed.

      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. Engage the 5 guides and 3 clips to install the package tray trim panel assembly.

      A011SIZ
  4. INSTALL REAR SEAT SHOULDER BELT COVER

    1. Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.

      A011UJR

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  5. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER

    1. Engage the 2 guides and 2 claws to install the child restraint seat tether anchor cover.

      A011RTQ

      Tech Tips

      Use the same procedure for the other 2 child restraint seat tether anchor covers.

  6. INSTALL CENTER STOP LIGHT SET

    1. Connect the connector.

    2. Temporarily install the center stop light set.

    3. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.

      A011UP5E01
  7. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

    1. Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.

      A011T4XE01
      Text in Illustration
      *1 Protruding Part
      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      • Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.

      • Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

  8. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH

    1. Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
  9. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)

    1. Connect the floor anchor of the rear seat outer belt assembly with the bolt.

      A011V8RE01
      Text in Illustration
      *1 Protruding Part
      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

  10. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)

    1. Connect the floor anchor of the rear seat outer belt assembly with the bolt.

      A011S4QE01
      Text in Illustration
      *1 Protruding Part
      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

  11. INSTALL ROOF SIDE INNER GARNISH LH

    1. Engage the guide.

    2. Engage the 5 clips to install the roof side inner garnish LH.

  12. INSTALL ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    1. Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      A011U1SE01
      Text in Illustration
      *1 Alignment Mark (Pink)

      Note

      After installation, check that the corners fit correctly.

  14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    1. Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      A011SNSE01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Note

      After installation, check that the corners fit correctly.

  15. INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    1. Engage the hook.

    2. Install the rear side seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Connect the connector.

    4. Connect the rear seat outer belt to the rear seat shoulder belt guide.

  16. INSTALL REAR SEATBACK ASSEMBLY LH

    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
  17. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

    1. Install the rear seat inner with center belt assembly RH with the bolt.

      A011UVBE01
      Text in Illustration
      *1 Protruding Part
      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      • Install the rear seat inner with center belt assembly RH with the arrow on the anchor part facing the front of the vehicle.

      • Do not allow the anchor part of the rear seat inner with center belt assembly RH to overlap the protruding parts of the floor panel.

  18. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH

    1. Install the child restraint seat anchor bracket sub-assembly RH with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
  19. INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    1. Engage the hook.

    2. Install the rear side seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    3. Connect the connector.

    4. Connect the rear seat outer belt to the rear seat shoulder belt guide.

  20. INSTALL REAR SEATBACK ASSEMBLY RH

    1. Place the rear seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
  21. INSTALL INNER LUGGAGE COMPARTMENT TRIM PAD

    1. Install the inner luggage compartment trim pad.

  22. INSTALL REAR SEAT CUSHION LOCK HOOK

    1. Engage the claw to install a new rear seat cushion lock hook.

      A011U4Y

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  23. INSTALL REAR SEAT CUSHION ASSEMBLY

    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.

      A011U81
    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  25. INSPECT SRS WARNING LIGHT

    Click here