AIRBAG SYSTEM, Diagnostic DTC:B1820/55, B1821/55, B1822/55, B1823/55

DTC Code DTC Name
B1820/55 Short in Side Squib RH Circuit
B1821/55 Open in Side Squib RH Circuit
B1822/55 Short to GND in Side Squib RH Circuit
B1823/55 Short to B+ in Side Squib RH Circuit

DESCRIPTION

The front side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1820/55

  • The airbag sensor assembly receives a line short circuit signal in the front side squib RH circuit during primary check.

  • Front side squib RH malfunction

  • Airbag sensor assembly malfunction

  • No. 2 floor wire

  • Front seat airbag assembly RH (Front side squib RH)

  • Airbag sensor assembly
B1821/55

  • The airbag sensor assembly receives an open circuit signal in the front side squib RH circuit.

  • Front side squib RH malfunction

  • Airbag sensor assembly malfunction
B1822/55

  • The airbag sensor assembly receives a short circuit to ground signal in the front side squib RH circuit.

  • Front side squib RH malfunction

  • Airbag sensor assembly malfunction
B1823/55

  • The airbag sensor assembly receives a short circuit to B+ signal in the front side squib RH circuit.

  • Front side squib RH malfunction

  • Airbag sensor assembly malfunction

WIRING DIAGRAM

A011V7WE58

INSPECTION PROCEDURE

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

Tech Tips

  • Perform the simulation method by selecting check mode (Signal Check) using the Techstream Click here.

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road Click here.

PROCEDURE

  1. CHECK CONNECTORS

    1. Turn the ignition switch off.

      A011TBUE01

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the front seat airbag assembly RH and airbag sensor assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the front seat airbag assembly RH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.

      OK
      The short spring is not deformed or damaged.
      Text in Illustration
      *1 Front Seat Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  2. CHECK FRONT SEAT AIRBAG ASSEMBLY RH (FRONT SIDE SQUIB RH)

    1. Connect the connector to the airbag sensor assembly.

      A011SDAE05

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the front seat airbag assembly RH (front side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note

      • Do not forcibly insert SST into the terminals of the connector when connecting it.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.

      Tech Tips

      Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Disconnect SST from connector C.

      Text in Illustration
      *1 Front Seat Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly RH)
    NG

    CHECK NO. 2 FLOOR WIRE Click here

    OK

    REPLACE FRONT SEAT AIRBAG ASSEMBLY RH Click here

  3. CHECK NO. 2 FLOOR WIRE

    1. Disconnect the No. 2 floor wire from the airbag sensor assembly.

      A011UBEE05

    2. Check for a short to B+ in the circuit.

      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        Oz1-1 (SFR+) - Body ground Ignition switch ON Below 1 V
        Oz1-2 (SFR-) - Body ground Ignition switch ON Below 1 V

      4. Turn the ignition switch off.

      5. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check for an open in the circuit.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Oz1-1 (SFR+) - Oz1-2 (SFR-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Oz1-1 (SFR+) - Body ground Always 1 MΩ or higher
        Oz1-2 (SFR-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.

      1. Release the activation prevention mechanism built into connector B Click here.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Oz1-1 (SFR+) - Oz1-2 (SFR-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

        Text in Illustration
        *1 Front Seat Airbag Assembly RH
        *2 Airbag Sensor Assembly
        *3 No. 2 Floor Wire
        *a

        Front view of wire harness connector

        (to Front Seat Airbag Assembly RH)
    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK DTC

    1. Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.

      A011SBNE01

    2. Connect the cable to the negative (-) battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON, and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      OK
      DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.

      Tech Tips

      Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.

      Text in Illustration
      *1 Front Seat Airbag Assembly RH
      *2 Airbag Sensor Assembly
    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here