REAR DOOR LOCK INSTALLATION

Tech Tips

  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

    1. Install the rear door inside locking cable assembly.

      A011SON

    2. Engage the 3 claws.

      A011SOQ

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

    1. Install the rear door lock remote control cable assembly.

      A011T85

    2. Engage the claw.

      A011TFZ

  3. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Note

    • When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock with motor assembly.

    1. Apply MP grease to the sliding parts of the rear door lock with motor assembly.

    2. When reusing the rear door lock with motor assembly.

      1. Install a new door lock wiring harness seal to the rear door lock with motor assembly.

    3. Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.

      A011T4EE01
      Text in Illustration
      *1 Release Plate

    4. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.

    5. Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

    1. Slide the rear door glass sub-assembly to install it as shown in the illustration.

      A011R2Y

  5. INSTALL REAR DOOR QUARTER WINDOW GLASS

    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

      A011TT5

  6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

    1. Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

      A011V10

  7. INSTALL REAR DOOR GLASS RUN

    1. Install the rear door glass run.

      A011UWH

  8. INSTALL REAR DOOR WEATHERSTRIP

    1. Install the upper part of rear door weatherstrip as shown in the illustration.

      A011T51

  9. INSTALL REAR DOOR SERVICE HOLE COVER

    1. Apply new butyl tape to the rear door panel.

    2. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

      A011RC6E01
      Text in Illustration
      *1 Reference Point

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

    1. Install the rear door inner glass weatherstrip.

      A011S1G

  11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    1. Install the No. 1 door scuff plate clamp as shown in the illustration.

      A011UP3

    2. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

      A011TOJE01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

    3. Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

      A011R1YE01
      Text in Illustration
      *1 Reference Boss

    4. Engage the 8 clips and install the rear door trim board sub-assembly.

      A011U67

    5. Install the 3 screws.

    6. If protective tape has been applied, remove it.

  12. INSTALL REAR ARMREST ASSEMBLY

    1. Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

      A011SYR

  13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    1. Connect the connector.

    2. Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

      A011R9V

  14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    1. Engage the 3 claws to install the rear door inside handle bezel plug.

      A011QNY

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. CHECK POWER WINDOW CONTROL SYSTEM

    Click here