REAR DOOR LOCK REMOVAL

Tech Tips

  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

    1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

      A011SXD

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    1. Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

      A011R4A

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE REAR ARMREST ASSEMBLY

    1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

      A011VBG

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    1. Put protective tape around the rear door panel.

      A011S38E01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 3 screws.

      A011U67

    3. Using a clip remover, disengage the 8 clips.

    4. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

      A011UCCE01
      Text in Illustration
      *1 Reference Boss
      *2 Rear Door Inner Glass Weatherstrip

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

      A011UFW

    8. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

      A011TZFE01
      Text in Illustration
      *1 Screwdriver

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

    1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

      A011TBLE01
      Text in Illustration
      *1 Screwdriver

  8. REMOVE REAR DOOR SERVICE HOLE COVER

    1. Disconnect the connector and remove the rear door service hole cover.

      A011SGK

      Tech Tips

      Remove any remaining butyl tape from the door.

  9. DISCONNECT REAR DOOR WEATHERSTRIP

    1. Disconnect the upper part of rear door weatherstrip as shown in the illustration.

      A011T25

  10. REMOVE REAR DOOR GLASS RUN

    1. Remove the rear door glass run.

      A011UWH

  11. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

    1. Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      A011V10

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  12. REMOVE REAR DOOR QUARTER WINDOW GLASS

    1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

      A011V1M

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      A011R7S

      Note

      Do not damage the door glass.

  14. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

    1. Using a T30 "TORX" socket wrench, remove the 3 screws.

      A011S6QE01
      Text in Illustration
      *1 Release Plate

    2. Move the rear door lock with motor assembly downward and pull the release plate out of the rear door outside handle frame.

    3. When reusing the rear door lock with motor assembly.

      1. Remove the door lock wiring harness seal from the rear door lock with motor assembly.

        A011TPV

  15. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

    1. Using a screwdriver, disengage the claw.

      A011QXM

    2. Remove the rear door lock remote control cable assembly.

      A011T3Q

  16. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

    1. Using a screwdriver, disengage the 3 claws.

      A011SHX

    2. Remove the rear door inside locking cable assembly.

      A011SR8