LIN COMMUNICATION SYSTEM TERMINALS OF ECU

  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    1. Disconnect the MB and 3D instrument panel junction block assembly connectors.

      A011QP5E31

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connectors disconnected.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      3D-31 (BECU) - Body ground V - Body ground Battery power supply Always 11 to 14 V
      MB-11 (GND1) - Body ground - Ground Always Below 1 Ω

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the MB and 3D instrument panel junction block assembly connectors.

    4. Check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      3B-30 (LIN2) - 3B-7 (GND1) P - W-B LIN communication line Ignition switch ON Pulse generation

      If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.

  2. CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

    1. Disconnect the K9 power window regulator motor assembly (for driver side) connector.

      A011TY2E15

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      K9-2 (B) - K9-1 (E) W - W-B Battery power supply Always 11 to 14 V
      K9-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the K9 power window regulator motor assembly (for driver side) connector.

    4. Check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      K9-9 (LIN) - K9-1 (E) P - W-B LIN communication line Ignition switch ON Pulse generation

      If the result is not as specified, the power window regulator motor assembly (for driver side) may be malfunctioning.

  3. CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Sliding Roof System)

    1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

      A011TGAE01

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      S4-8 (B) - S4-12 (E) B - W-B Battery power supply Always 11 to 14 V
      S4-12 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

    4. Check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      S4-11 (MPX1) - S4-12 (E) P - W-B LIN communication line Ignition switch ON Pulse generation

      If the result is not as specified, the sliding roof ECU (sliding roof drive gear sub-assembly) may be malfunctioning.

  4. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

      A011TKNE30

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tech Tips

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      A43-2 (+B) - A43-11 (E) W - W Battery power supply Always 11 to 14 V
      A43-11 (E) - Body ground W - Body ground Ground Always Below 1 Ω

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

    4. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      I78-5 (IG) - A43-11 (E) LG - W IG power supply Ignition switch ON 11 to 14 V
      I78-5 (IG) - A43-11 (E) LG - W IG power supply Ignition switch off Below 1 V
      I78-17 (LIN) - A43-11 (E) V - W LIN communication line Ignition switch ON Pulse generation

      If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.

  5. CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

    1. Disconnect the I24 steering lock ECU (steering lock actuator assembly) connector.

      A011UDPE16

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I24-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
      I24-7 (B) - Body ground B - Body ground Battery power supply Always 11 to 14 V
      I24-6 (IG2) - Body ground LG - Body ground IG power supply Ignition switch ON 11 to 14 V

      If the result is not as specified, there may be a malfunction on the wire harness side.

    3. Reconnect the I24 steering lock ECU (steering lock actuator assembly) connector.

    4. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      I24-5 (LIN) - I24-1 (GND) V - W-B LIN communication line Ignition switch ON Pulse generation

      If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.