BLIND SPOT MONITOR SYSTEM FREEZE FRAME DATA

  1. FREEZE FRAME DATA

    1. Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.

  2. CHECK FREEZE FRAME DATA

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

    4. Turn the Techstream on.

    5. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.

    6. According to the display on the Techstream, display the Freeze Frame Data for the selected DTC.

      Blind Spot Monitor Master
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main Switch Blind spot monitor main switch (warning canceling switch assembly) / ON or OFF

      ON: Blind spot monitor main switch (warning canceling switch assembly) on

      OFF: Blind spot monitor main switch (warning canceling switch assembly) off

      -
      Warning Indicator Turning on (Master) State of the outer rear view mirror indicator RH turning on / OFF or ON

      OFF: The following conditions are not met

      • ON: All of the following conditions are met

        • Not during initial check

        • Vehicle detected in left hand side warning area

        • Left turn signal: off

        • Vehicle speed 16 km/h (10 mph) or more

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      -
      Warning Indicator Flashing (Master) State of the outer rear view mirror indicator RH flashing / OFF or ON

      OFF: The following conditions are not met

      • ON: All of the following conditions are met

        • Not during initial check

        • Vehicle detected in left hand side warning area

        • Left turn signal: on

        • Vehicle speed 16 km/h (10 mph) or more

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      -
      Main Switch Indicator Status State of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) / OFF or ON

      OFF: Indicator not illuminated

      ON: Indicator illuminated

      -
      Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V

      Indicator illuminated: 2.5 to 7.5 V

      Indicator not illuminated: Below 1 V

      -
      Warning Indicator Input Circuit Current The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA

      Indicator illuminated: 5 to 100 mA

      Indicator not illuminated: 0 mA

      -
      Main Switch Indicator Input Circuit Voltage Blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) voltage / Min.: 0 V, Max.: 25.5 V Always: 9 to 16 V -
      Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      -
      Reverse (Only for AT/CVT) State of the shift position R signal / OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -
      Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering angle sensor / Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      -
      Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
      Number of DTC Number of DTC / Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      -
      Blind Spot Monitor Slave
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator LH turning on / OFF or ON

      OFF: The following conditions are not met

      • ON: All of the following conditions are met

        • Not during initial check

        • Vehicle detected in right hand side warning area

        • Right turn signal: OFF

        • Vehicle speed 16 km/h (10 mph) or more

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      -
      Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator LH flashing / OFF or ON

      OFF: The following conditions are not met

      • ON: All of the following conditions are met

        • Not during initial check

        • Vehicle detected in right hand side warning area

        • Vehicle speed 16 km/h (10 mph) or more

        • Right turn signal: ON

        • Shift lever in any position except R

        • Blind spot monitor warning light not illuminated

      -
      Buzzer Sound Status State of the rear cross traffic alert buzzer (blind spot monitor buzzer) / OFF or ON

      OFF: Buzzer not sounding

      ON: Buzzer sounding

      -
      Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V

      Indicator illuminated: 2.5 to 7.5 V

      Indicator not illuminated: Below 1 V

      -
      Warning Indicator Input Circuit Current The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA

      Indicator illuminated: 5 to 100 mA

      Indicator not illuminated: 0 mA

      -
      Buzzer Input Circuit Voltage Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V

      Buzzer not sounding: 11 to 14 V

      Buzzer sounding: Alternating between 0 to 14 V

      -
      Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      -
      Reverse (Only for AT/CVT) State of the shift position R signal / OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -
      Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering angle sensor / Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      -
      Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
      Number of DTC Number of DTC / Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      -
  3. CLEAR FREEZE FRAME DATA

    Note

    Clearing the DTCs will also clear the Freeze Frame Data

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

    4. Turn the Techstream on.

    5. Clear the DTCs and Freeze Frame Data.