PARKING BRAKE CABLE REMOVAL

Tech Tips

  • The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.

  • Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.

  1. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY

    Click here

  2. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

    1. Pull up the parking brake pedal claw.

      A011T72

      Note

      Do not damage the No. 1 parking brake cable assembly.

    2. Remove the adjusting nut.

      A011SU6

    3. Remove the clip from the No. 1 parking brake cable assembly.

      A011RRR

    4. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.

  3. REMOVE REAR DOOR SCUFF PLATE LH

    1. Disengage the 6 claws and remove the rear door scuff plate LH.

      A011RO9

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

    1. Disconnect the rear door opening trim weatherstrip LH.

  5. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

    1. Disengage the 3 claws and remove the lap belt outer anchor cover.

      A011UT6

  6. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

      A011STL

  7. REMOVE CENTER PILLAR LOWER GARNISH LH

    1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

      A011T7N

  8. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE FRONT SEAT ASSEMBLY LH

  14. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  15. REMOVE AUDIO AMPLIFIER COVER (for 10 Speakers)

    1. Using a clip remover, remove the 2 clips and audio amplifier cover.

      A011R6Q

  16. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)

    1. Remove the bolt and disconnect the ground wire.

      A011UVH

    2. Disconnect each connector.

    3. Disengage the clamp.

    4. Remove the bolt.

      A011V49

    5. Disengage the 2 guides and remove the stereo component amplifier assembly with bracket.

  17. REMOVE AUDIO AMPLIFIER COVER (w/ Manual (SOS) Switch)

    1. Using a clip remover, remove the 2 clips and audio amplifier cover.

      A011UV5

  18. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH BACK-UP BATTERY (w/ Manual (SOS) Switch)

    1. Disconnect each connector.

      A011UKC

    2. Disengage the 3 clamps.

    3. Remove the bolt.

      A011RS2

    4. Disengage the 2 guides and remove the DCM (telematics transceiver) with back-up battery.

  19. REMOVE FLOOR CARPET HOOK

    1. Disengage the 6 guides.

      A011QUYE01
      Text in Illustration
      *A for LH Side
      *B for RH Side

    2. Disengage the 6 claws and remove the 6 floor carpet hooks.

      A011U2SE01
      Text in Illustration
      *A for LH Side
      *B for RH Side

  20. REMOVE NO. 4 CROSS MEMBER FLOOR REINFORCEMENT SUB-ASSEMBLY

    1. Remove the screw.

      A011RHP

    2. Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

      A011TLD

    3. Turn back the floor carpet to a position where the No. 4 cross member floor reinforcement sub-assembly can be removed.

    4. Remove the 8 bolts and No. 4 cross member floor reinforcement sub-assembly.

      A011V9G

  21. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY

    1. Separate the No. 3 parking brake cable assembly from the parking brake equalizer.

      A011T9BE01
      Text in Illustration
      *1 Parking Brake Equalizer
      *2 No. 2 Parking Brake Cable Assembly
      *3 No. 3 Parking Brake Cable Assembly
      *4 No. 4 Parking Brake Cable Assembly

    2. Separate the No. 2 parking brake cable assembly to remove the parking brake equalizer.

    3. Slide the parking brake equalizer and rubber boot.

      A011UMLE01
      Text in Illustration
      *1 Rubber Boot
      *2 Parking Brake Equalizer
      *3 No. 4 Parking Brake Cable Assembly

    4. Remove the No. 4 parking brake cable assembly from the parking brake equalizer.

  22. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2AR-FE)

    Click here

  23. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for 2AR-FE)

    1. Remove the 3 nuts and front No. 2 floor heat insulator.

      A011T45

  24. REMOVE PARKING BRAKE SHOE LEVER

    Click here

  25. REMOVE NO. 2 FLOOR UNDER COVER (for LH Side)

    1. w/ Floor Under Cover:

      1. Remove the 2 bolts and 2 clips.

        A011V11
        Text in Illustration
        A011T1X Bolt
        A011V7Q Nut (attached to under cover)

      2. Disengage the 3 nuts and remove the No. 2 floor under cover.

  26. REMOVE NO. 1 FLOOR UNDER COVER (for RH Side)

    1. Remove the 2 bolts.

      A011SYI
      Text in Illustration
      A011T1X Bolt
      A011V7Q Nut (attached to under cover)

    2. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.

  27. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

    1. Remove the clip from the No. 3 parking brake cable assembly.

      A011S0U

    2. Remove the bolt and separate the No. 3 parking brake cable assembly.

      A011SB8

    3. Remove the 4 bolts, nut and No. 3 parking brake cable assembly.

      A011U73

  28. REMOVE NO. 2 PARKING BRAKE CABLE CLAMP

    1. Remove the No. 2 parking brake cable clamp.