SFI SYSTEM, Diagnostic DTC:P0101

DTC Code DTC Name
P0101 Mass Air Flow Circuit Range / Performance Problem

DESCRIPTION

Refer to DTC P0102 Click here.

DTC No. DTC Detection Condition Trouble Area
P0101

All of the following conditions continue for more than 10 seconds (2 trip detection logic).

(a) The engine is running.

(b) The engine coolant temperature is 70°C (158°F) or higher.

(c) The throttle position sensor voltage is 0.2 V or higher, and less than 2 V.

(d) The average engine load value ratio is less than 0.83, or higher than 1.15 (varies with estimated engine load).

Average engine load value ratio = Average engine load based on mass air flow meter sub-assembly output / Average engine load estimated from driving conditions

(e) The average air fuel ratio is less than -20%, or higher than 20%.

  • Mass air flow meter sub-assembly

  • Intake system

  • PCV hose connections

MONITOR DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine fuel injection timing and to provide an appropriate air fuel ratio. Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the mass air flow meter sub-assembly. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The ECM monitors the average engine load value ratio to check the mass air flow meter sub-assembly for malfunctions. The average engine load value ratio is obtained by comparing the average engine load calculated from the MAF meter output to the average engine load estimated from the driving conditions, such as the engine speed and the throttle opening angle. If the average engine load value ratio is below the threshold value, the ECM determines that the intake air volume is low, and if the average engine load value ratio is above the threshold value, the ECM determines that the intake air volume is high.

If this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.

MONITOR STRATEGY

Related DTCs P0101: Mass air flow meter rationality
Required Sensors/Components (Main) Mass air flow meter sub-assembly
Required Sensors/Components (Related)

Crankshaft position sensor

Camshaft position sensor

Engine coolant temperature sensor

Throttle position sensor
Frequency of Operation Continuous
Duration 10 times
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored None
All of the following conditions are met -
|Throttle position sensor voltage - (learned throttle position sensor closed position voltage + (ISC voltage)| 0.2 V or higher, and less than 2 V
Time after engine start 5 seconds or more
Battery voltage 10.5 V or higher
Estimated load 30% or higher, and less than 70%
Engine coolant temperature 70°C (158°F) or higher
Mass air flow meter circuit fail (P0102, P0103) Not detected
Intake air temperature sensor circuit fail (P0112, P0113) Not detected
Engine coolant temperature sensor circuit fail (P0115, P0117, P0118) Not detected
Crankshaft position sensor circuit fail (P0335) Not detected
Throttle position sensor circuit fail (P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135) Not detected
EVAP system pressure sensor circuit fail (P0452, P0453) Not detected
Leak detection pump fail (P2401, P2402) Not detected
EVAP vent valve fail (P2419, P2420) Not detected

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met -
Average engine load value ratio Less than 0.83, or higher than 1.15 (varies with estimated engine load)
Average air fuel ratio Less than -20%, or higher than 20%

CONFIRMATION DRIVING PATTERN

A011TUHE15

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the ignition switch off and wait for at least 30 seconds.

  6. Turn the ignition switch to ON and turn the Techstream on.

  7. Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher [A].

  8. Drive the vehicle at approximately 80 km/h (50 mph) to 112 km/h (70 mph) for 5 minutes or more [B].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    Drive while keeping the engine load as stable as possible.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

  10. Read the pending DTCs.

    Tech Tips

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  12. Input the DTC: P0101.

  13. Check the DTC judgment result.

    Techstream Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs Click here.

    Tech Tips

    • If a permanent DTC is output, the system is malfunctioning.

    • If no permanent DTC is output, the system is normal.

WIRING DIAGRAM

Refer to DTC P0102 Click here.

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0101)

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P0101 is output A
      DTC P0101 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0101 are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART Click here

    A

  2. CHECK INTAKE SYSTEM

    1. Check the intake system for vacuum leaks Click here.

      OK
      No leaks from intake system.

      Tech Tips

      Perform "Inspection After Repair" after repairing or replacing the intake system Click here.

    NG

    REPAIR OR REPLACE INTAKE SYSTEM

    OK

  3. CHECK PCV HOSE CONNECTIONS

    1. Check the PCV hose connections Click here.

      OK
      PCV valve and hose are connected correctly and are not damaged.
    NG

    REPAIR OR REPLACE PCV HOSE

    OK

  4. REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

    1. Replace the mass air flow meter sub-assembly Click here.

      Tech Tips

      Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly Click here.

    NEXT

  5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the Techstream on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    11. Input the DTC: P0101.

    12. Check the DTC judgment.

      Result
      Techstream Display Description
      NORMAL

      • DTC judgment completed

      • System normal
      ABNORMAL

      • DTC judgment completed

      • System abnormal
      INCOMPLETE

      • DTC judgment not completed

      • Perform driving pattern after confirming DTC enabling conditions
      N/A

      • Unable to perform DTC judgment

      • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    NEXT

    END