EXHAUST PIPE INSTALLATION

  1. INSTALL HEATED OXYGEN SENSOR (for Bank 2)

    1. Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

      A011UTCE01
      Text in Illustration
      *a

      Fulcrum Length

      30 mm (1.18 in.)
      *b

      Fulcrum Length

      180 mm (7.09 in.)
      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 33 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note

      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 180 mm (7.09 in.) Click here.

      • The "with SST" torque value is effective when SST is parallel to the torque wrench.

  2. INSTALL HEATED OXYGEN SENSOR (for Bank 1)

    1. Using SST, install the heated oxygen sensor to the center exhaust pipe assembly.

      A011QQ2E01
      Text in Illustration
      *a

      Fulcrum Length

      30 mm (1.18 in.)
      *b

      Fulcrum Length

      180 mm (7.09 in.)
      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 33 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Note

      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 180 mm (7.09 in.) Click here.

      • The "with SST" torque value is effective when SST is parallel to the torque wrench.

  3. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    1. Install 2 new gaskets to the front exhaust pipe assembly.

    2. Connect the front exhaust pipe assembly to the No. 1 exhaust pipe support bracket (for Rear Side).

    3. Install the front exhaust pipe assembly with the 2 bolts and 2 nuts.

      Torque:
      55 N*m  { 561 kgf*cm, 40 ft.*lbf }

    4. Connect the 2 heated oxygen sensor connectors.

    5. Install the 2 wire harnesses to the clamp.

  4. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Front Side)

    1. Install the No. 1 exhaust pipe support bracket with the 2 nuts (for Front Side).

      Torque:
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }

  5. INSTALL ENGINE UNDER COVER RH

  6. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

  7. INSTALL CENTER EXHAUST PIPE ASSEMBLY

    1. Install a new gasket to the front exhaust pipe assembly.

    2. Connect the center exhaust pipe assembly to the exhaust pipe supports.

    3. Install the center exhaust pipe assembly with the 2 bolts and 2 nuts.

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }

  8. INSTALL EXHAUST PIPE DAMPER

    1. Install the exhaust pipe damper with the 2 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  9. INSTALL TAIL EXHAUST PIPE ASSEMBLY

    1. Install a new gasket to the center exhaust pipe assembly.

    2. Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.

    3. Install the tail exhaust pipe assembly with the 2 nuts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  10. INSTALL TAIL EXHAUST PIPE ASSEMBLY LH

    1. Install a new gasket to the center exhaust pipe assembly.

    2. Connect the tail exhaust pipe assembly LH to the 2 exhaust pipe supports.

    3. Install the tail exhaust pipe assembly LH with the 2 nuts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  11. INSPECT FOR EXHAUST GAS LEAK