SFI SYSTEM, Diagnostic DTC:P2111, P2112

DTC Code DTC Name
P2111 Throttle Actuator Control System - Stuck Open
P2112 Throttle Actuator Control System - Stuck Closed

DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

Tech Tips

This Electronic Throttle Control System (ETCS) does not use a throttle cable.

DTC No. DTC Detection Condition Trouble Area
P2111 The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).

  • Throttle actuator

  • Throttle with motor body assembly

  • Throttle valve

  • Wire harness or connector

  • ECM
P2112 The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).

  • Throttle actuator

  • Throttle with motor body assembly

  • Throttle valve

  • Wire harness or connector

  • ECM

MONITOR DESCRIPTION

The ECM determines that there is a malfunction in the ETCS when the throttle valve remains at a fixed angle despite a high drive current from the ECM. The ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Related DTCs

P2111: Throttle actuator stuck open

P2112: Throttle actuator stuck closed
Required Sensors/Components (Main) Throttle actuator (throttle with motor body assembly)
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None
P2111: Throttle Actuator Stuck Open
All of following conditions are met: -
System guard* judge condition On
Throttle actuator current 2 A or higher
Duty-cycle to close throttle 80% or higher
P2112: Throttle Actuator Stuck Closed
All of the following conditions are met: -
System guard* judge condition On
Throttle actuator current 2 A or higher
Duty-cycle to open throttle 80% or more
*: System guard set when following conditions are met: -
Throttle actuator On
Throttle actuator duty calculation Executing
Throttle position sensor fail Not detected
Throttle actuator current-cut operation Not executing
Throttle actuator power supply 4 V or higher
Throttle actuator fail Not detected

TYPICAL MALFUNCTION THRESHOLDS

P2111: Throttle Actuator Stuck Open
Throttle position sensor voltage No change
P2112: Throttle Actuator Stuck Closed
Throttle position sensor voltage No change

CONFIRMATION DRIVING PATTERN

A011T9PE01

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON and turn the Techstream on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the Techstream on [A].

  6. Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).

  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

  8. Read the pending DTCs.

    Tech Tips

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  10. Input the DTC: P2111 or P2112.

  11. Check the DTC judgment result.

    Techstream Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    Tech Tips

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs Click here.

    Tech Tips

    • If a permanent DTC is output, the system is malfunctioning.

    • If no permanent DTC is output, the system is normal.

FAIL-SAFE

When either of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 Click here.

INSPECTION PROCEDURE

Tech Tips

  • Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  • Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] Click here.

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P2111 or P2112 is output A
      DTC P2111 or P2112 and other DTCs are output B

      Tech Tips

      If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART Click here

    A

  2. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

    1. Check for contamination between the throttle valve and housing. If necessary, clean the throttle with motor body assembly. Also check that the throttle valve moves smoothly.

      OK
      Throttle valve is not contaminated with foreign objects and moves smoothly.

      Tech Tips

      Perform "Inspection After Repair" after cleaning the throttle with motor body assembly Click here.

    NG

    REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY Click here

    OK

  3. READ VALUE USING TECHSTREAM (THROTTLE POSITION)

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON and turn the Techstream on.

    7. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Throttle / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.

    8. Read the values displayed on the Techstream while wiggling the ECM wire harness.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.

      Result
      Result Proceed to
      Value in Data List changes when wire harness is wiggled, or DTC is output A
      Other than above B
    B

    CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112) Click here

    A

  4. REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)

    1. As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector Click here.

    NEXT

    END

  5. REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

    1. Replace the throttle with motor body assembly Click here.

      Tech Tips

      Perform "Inspection After Repair" after replacing the throttle with motor body assembly Click here.

    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the Techstream on.

    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P2111 or P2112 is output B
    B

    REPLACE ECM Click here

    A

    END