TRANSMISSION CONTROL CABLE INSTALLATION

  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    Note

    Before installing the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.

    1. Pass the transmission control cable assembly from the cabin to the engine compartment.

    2. Install the transmission control cable assembly with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    3. Install the dash panel insulator to the original position.

    4. Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.

    5. Connect the transmission control cable assembly to the control shaft lever with the nut.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.

    6. Connect the wire harness clamp.

    7. Engage the 2 claws to connect the transmission control cable assembly.

    8. Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

      A011R7PE03
      Text in Illustration
      *1 Slider
      *2 Lock Piece
      *a Slide
      *b Pull

    9. Install the end of transmission control cable to the lower shift lever assembly.

      A011V1LE01
      Text in Illustration
      *1 Lock Piece

      Note

      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    10. Push the lock piece into the adjuster case.

      Note

      • Check that the park/neutral position switch and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

  2. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY

    1. Install the No. 1 parking brake cable assembly with the bolt and nut.

      Torque:
      Bolt
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }
      Nut
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  3. INSTALL ACCELERATOR PEDAL SENSOR ASSEMBLY

    Note

    • Avoid physical shock to the accelerator pedal sensor assembly.

    • Do not disassemble the accelerator pedal sensor assembly.

    • This accelerator pedal does not require lubrication.

    • Do not apply oil or other lubrication to the accelerator pedal sensor assembly. If applied, the accelerator pedal sensor assembly must be replaced.

    1. Temporarily install the accelerator pedal sensor assembly with the 2 bolts.

      A011RZTE02

    2. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the accelerator pedal sensor assembly connector.

  4. INSTALL AIRBAG SENSOR ASSEMBLY

    Click here

  5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    1. Install the air cleaner case sub-assembly to the inlet No. 1 air cleaner.

      A011TV6E01

    2. Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.

      Text in Illustration
      *1 Air Cleaner Case Sub-assembly
      *2 Inlet No. 1 Air Cleaner
      *a Projection
      *b Hole

    3. Tighten the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    4. Connect the wire harness clamp, connector, vacuum hose and No. 1 fuel vapor feed hose.

  6. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    1. Connect the air cleaner cap sub-assembly to the throttle with motor body assembly with the hose clamp.

    2. Install the air cleaner cap with hose to the air cleaner case with the 2 clamps.

    3. Connect the wire harness clamp and mass air flow meter connector.

    4. Connect the 3 hoses.

    5. Connect the ventilation hose.

    6. Connect the mass air flow meter connector and wire harness clamp.

  8. INSTALL INLET NO. 2 AIR CLEANER

    1. Install the inlet No. 2 air cleaner to the air cleaner case sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the 2 wire harness clamps and vacuum hose clamp.

  9. INSTALL COOL AIR INTAKE DUCT SEAL

    1. Install the cool air intake duct seal with the 7 clips.

  10. INSPECT SHIFT LEVER POSITION

    1. When the shift lever is moved from P to R with the engine switch on (IG) and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.