SHIFT PADDLE SWITCH INSTALLATION

Note

  • Do not replace the spiral cable with the battery connected and the engine switch on (IG).

  • Do not rotate the spiral cable without the steering wheel with the battery connected and the engine switch on (IG).

  • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

  • Do not remove the steering sensor from the spiral cable.

  1. CONNECT NO. 1 SWITCH WIRE

    1. Connect the 2 No. 1 switch wire connectors to the 2 shift paddle switches (transmission shift switch assembly).

    2. Install new 2 clamps as shown in the illustration.

      A011RVTE01
      Text in Illustration
      *1 Clamp
      *a 0 to 40°
      *b 1 to 3 mm

    3. Engage the 5 guides to install the No. 1 switch wire.

  2. INSTALL SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

    1. Engage the 4 pins and install the 2 shift paddle switches (transmission shift switch assembly) with the 2 screws.

      Torque:
      1.3 N*m  { 13 kgf*cm, 12 in.*lbf }

      Note

      Make sure that the brackets are securely installed.

  3. INSTALL STEERING PAD SWITCH ASSEMBLY

    1. Engage the 2 claws, 2 pins and 2 guides to install the steering pad switch assembly.

    2. Install the 2 screws.

      Torque:
      2.4 N*m  { 24 kgf*cm, 21 in.*lbf }

    3. Engage the clamp.

    4. Connect the No. 1 switch wire connector.

    5. Connect the steering pad switch connector to the spiral cable sub-assembly.

    6. Pass the wire harness over the 2 guides.

      A011TGZ

  4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  5. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check if the spiral cable with sensor sub-assembly is centered.

      A011TTFE01
      Text in Illustration
      A011TKF Colored Part

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the part indicated by A is positioned at the top and the colored part shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.

      Note

      • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

      • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      1. While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

        A011RUC
        Text in Illustration
        A011V7R Interlock

      2. Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored part shown in the illustration is visible.

        A011SF9
        Text in Illustration
        A011TKF Colored Part
        A011V7R Interlock

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  6. INSTALL STEERING WHEEL ASSEMBLY

    1. Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

      A011TLXE01
      Text in Illustration
      *a Matchmark

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly and steering wheel assembly.

  7. CHECK STEERING WHEEL CENTER POINT

  8. INSTALL HORN BUTTON ASSEMBLY

    Click here