ВЫПУСКНАЯ ТРУБА УСТАНОВКА


  1. INSTALL NO. 2 HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    1. A015BIH

      Temporarily install the sensor to the exhaust pipe by hand.

    2. A015DPUE02
      Text in Illustration
      *1 Fulcrum Length

      Using SST, tighten the sensor.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification Click here.

      • Make sure SST and the wrench are connected in a straight line.

  2. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    1. Temporarily install the sensor to the exhaust pipe by hand.

    2. A015DPUE02
      Text in Illustration
      *1 Fulcrum Length

      Using SST, tighten the sensor.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification Click here.

      • Make sure SST and the wrench are connected in a straight line.

  3. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 2 new nuts.

      Torque:
      54 N*m  { 551 kgf*cm, 40 ft.*lbf }

    2. Install the wire harness clamp bracket of the oxygen sensor to the transmission with the bolt.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

    3. Connect the heated oxygen sensor connector.

  4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY


    1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 2 new nuts.

      Torque:
      54 N*m  { 551 kgf*cm, 40 ft.*lbf }

    2. Install the wire harness clamp bracket of the oxygen sensor to the transmission with the bolt.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

    3. Connect the heated oxygen sensor connector.

  5. INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. Install 2 new gaskets to the front exhaust pipe and front No. 2 exhaust pipe.

    2. Install the center exhaust pipe to the 3 exhaust pipe supports, and then install the 4 bolts.

      Torque:
      48 N*m  { 489 kgf*cm, 35 ft.*lbf }

  6. INSTALL EXHAUST PIPE DAMPER


    1. Install the exhaust pipe damper to the tailpipe with the 2 bolts.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

  7. INSTALL TAILPIPE ASSEMBLY


    1. Install the tailpipe to the 2 exhaust pipe supports.

    2. Install a new gasket to the center exhaust pipe.

    3. Connect the tailpipe to the center exhaust pipe.

    4. A0158T9E01
      Text in Illustration
      *1 Gasket
      *a Top
      *b LH Side
      *c Front

      Attach a new clamp to the tailpipe and center exhaust pipe. Then install the bolt to the clamp.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Tech Tips

      Install the clamp within the angle range shown in the illustration.

  8. INSPECT FOR EXHAUST GAS LEAK

  9. INSTALL NO. 2 ENGINE UNDER COVER


    1. Установите защиту картера двигателя № 2 и закрепите ее 2 болтами.

      Torque:
      29 Н*м  { 296 кгс*см, 21 фунт-сила-фут }