Click here

ГОЛОВКА БЛОКА ЦИЛИНДРОВ ПОВТОРНАЯ СБОРКА

Click here
Click here
  1. Click here

    INSTALL STUD BOLT

    Note:

    If the stud bolt is deformed or its threads are damaged, replace it.


    1. A015B3KE02

      Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

      for stud bolts A, B, C and D
      9.0 N*m 92 kgf*cm 80 in.*lbf
      Table 1. Text in Illustration
      *A LH for Intake Side *B LH for Exhaust Side
      *C LH for Front Side *D RH for Intake Side
      *E RH for Exhaust Side *F RH for Front Side
  2. Click here

    INSTALL NO. 2 STRAIGHT SCREW PLUG

    Note:

    If water leaks from the No. 2 straight screw plug or the plug is corroded, replace it.


    1. Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.

      85 N*m 867 kgf*cm 63 ft.*lbf
      Table 2. Text in Illustration
      *A LH
      *B RH
  3. Click here

    INSTALL NO. 1 STRAIGHT SCREW PLUG

    Note:

    If water leaks from the No. 1 straight screw plug or the plug is corroded, replace it.


    1. Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 straight screw plugs.

      44 N*m 449 kgf*cm 32 ft.*lbf
      Table 3. Text in Illustration
      *A LH
      *B RH
  4. Click here

    INSTALL VALVE SPRING SEAT


    1. Install the valve spring seats to the cylinder head.

  5. Click here

    INSTALL VALVE STEM OIL SEAL


    1. A0159QYE18

      Apply a light coat of engine oil to new oil seals.

      Table 4. Text in Illustration
      *A Intake Side
      *B Exhaust Side
      *1 Brown
      *2 Gray
      Note:

      Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side can cause installation problems later.

      Tip:

      The intake valve oil seals are brown and the exhaust valve oil seals are gray.

    2. A0155Z1E04

      Using SST, push in the oil seals.

      09201-41020
      Table 5. Text in Illustration
      *a CORRECT
      *b INCORRECT
      Note:

      Failure to use SST will cause the seal to be damaged or improperly seated.

  6. Click here

    INSTALL INTAKE VALVE


    1. A015BZQE32

      Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

    2. Install the valve, compression spring and spring retainer to the cylinder head.

      Table 6. Text in Illustration
      *a 40 mm (1.57 in.) or more
      Note:

      Install the same parts in the same combination to their original locations.

    3. A015DXPE01

      Using SST and wooden blocks, compress the spring and install the retainer locks.

      09202-70020 09202-00010
    4. A0159J5

      Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note:

      Be careful not to damage the retainer.

  7. Click here

    INSTALL EXHAUST VALVE


    1. A015DG8E30

      Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.

    2. Install the valve, compression spring and spring retainer to the cylinder head.

      Table 7. Text in Illustration
      *a 40 mm (1.57 in.) or more
      Note:

      Install the same parts in the same combination to their original locations.

    3. A015891E01

      Using SST and wooden blocks, compress the spring and install the retainer locks.

      09202-70020 09202-00010
    4. A015B0W

      Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note:

      Be careful not to damage the retainer.