РЕЛЕ ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ


  1. INSPECT INTEGRATION RELAY (IG2)


    1. Measure the resistance of the IG2 MAIN fuse.


      1. Remove the IG2 MAIN fuse from the integration relay.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        IG2 MAIN fuse Always Below 1 Ω

        If the result is not as specified, replace the IG2 MAIN fuse.

      3. Install the IG2 MAIN fuse to the integration relay.

    2. A015CBXE06
      Text in Illustration
      *a

      Component without harness connected

      (Integration Relay)

      Measure the resistance of the ignition relay No. 2 (IG2) circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
        Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω

        If the result is not as specified, replace the integration relay.

  2. INSPECT INTEGRATION RELAY (EFI)


    1. Measure the resistance of the EFI MAIN fuse.


      1. Remove the EFI MAIN fuse from the integration relay

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        EFI MAIN fuse Always Below 1 Ω

        If the result is not as specified, replace the EFI MAIN fuse.

      3. Install the EFI MAIN fuse to the integration relay.

    2. A015CBXE06
      Text in Illustration
      *a

      Component without harness connected

      (Integration Relay)

      Measure the resistance of the EFI relay circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
        Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω

        If the result is not as specified, replace the integration relay.

  3. INSPECT EFI NO. 2 RELAY


    1. A015CKTE01

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage is applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  4. INSPECT INTEGRATION RELAY (A/F)


    1. Measure the resistance of the A/F fuse.


      1. Remove the A/F fuse from the integration relay.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        A/F fuse Always Below 1 Ω

        If the result is not as specified, replace the A/F fuse.

      3. Install the A/F fuse to the integration relay.

    2. A015CBXE07
      Text in Illustration
      *a

      Component without harness connected

      (Integration Relay)

      Measure the resistance of the A/F sensor heater relay circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1A-4 Battery voltage is not applied to terminals 1A-2 and 1A-3 10 kΩ or higher
        Battery voltage is applied to terminals 1 A-2 and 1A-3 Below 1 Ω

        If the result is not as specified, replace the integration relay.

  5. INSPECT MAIN BODY ECU (IG1 NO. 1)


    1. Measure the resistance according to the value(s) in the table below.

      A0156OXE02
      Text in Illustration
      *a

      Component without harness connected

      (Main Body ECU)

      		 - -
      Standard Resistance
      Tester Connection Condition Specified Condition
      2A-1 - 2B-17 Battery voltage is not applied to terminals 2B-5 and 2D-43 10 kΩ or higher
      Battery voltage is applied to terminals 2B-5 and 2D-43 Below 1 Ω

      If the result is not as specified, replace the main body ECU.

  6. INSPECT STARTER RELAY (ST)


    1. A015BM6E06

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the starter relay.

  7. INSPECT STARTER CUT RELAY (ST CUT)


    1. A015APZE26

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the starter relay.

  8. INSPECT MAIN BODY ECU (ACC RELAY)

    A01569EE02
    Text in Illustration
    *a

    Component without harness connected

    (Main Body ECU)

    		 - -

    1. Measure the resistance of the ACC relay circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2A-1 - 2D-8 Battery voltage not applied between 2D-45 and 2D-62 10 kΩ or higher
        Battery voltage applied between 2D-45 and 2D-62 Below 1 Ω

        If the result is not as specified, replace the main body ECU.