Click here

СИСТЕМА SFI Fuel Injector Circuit

Click here
Click here
DTC Code DTC Name
  Fuel Injector Circuit
Click here

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

Click here

WIRING DIAGRAM

Refer to DTC P0300 (Click here).

Click here

INSPECTION PROCEDURE

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Click here

PROCEDURE


  1. Click here

    CHECK INJECTOR ASSEMBLY (POWER SOURCE)


    1. Disconnect the fuel injector connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Cylinder Tester Connection Switch Condition Specified Condition
      No. 1 a5-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 2 a1-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 3 a6-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 4 a2-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 5 a7-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 6 a3-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 7 a8-2 - Body ground Engine switch on (IG) 11 to 14 V
      No. 8 a4-2 - Body ground Engine switch on (IG) 11 to 14 V

  2. Click here

    INSPECT FUEL INJECTOR ASSEMBLY


    1. Inspect the fuel injector (Click here).


  3. Click here

    CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)


    1. Disconnect the fuel injector connector.

    2. Disconnect the C45 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Cylinder Tester Connection Condition Specified Condition
      No. 1 a5-1 - Body ground Always 10 kΩ or higher
      a5-1 - C45-86 (#10) Always Below 1 Ω
      No. 2 a1-1 - Body ground Always 10 kΩ or higher
      a1-1 - C45-109 (#20) Always Below 1 Ω
      No. 3 a6-1 - Body ground Always 10 kΩ or higher
      a6-1 - C45-85 (#30) Always Below 1 Ω
      No. 4 a2-1 - Body ground Always 10 kΩ or higher
      a2-1 - C45-108 (#40) Always Below 1 Ω
      No. 5 a7-1 - Body ground Always 10 kΩ or higher
      a7-1 - C45-84 (#50) Always Below 1 Ω
      No. 6 a3-1 - Body ground Always 10 kΩ or higher
      a3-1 - C45-107 (#60) Always Below 1 Ω
      No. 7 a8-1 - Body ground Always 10 kΩ or higher
      a8-1 - C45-83 (#70) Always Below 1 Ω
      No. 8 a4-1 - Body ground Always 10 kΩ or higher
      a4-1 - C45-106 (#80) Always Below 1 Ω

  4. Click here

    INSPECT INTEGRATION RELAY (IG2)


    1. Inspect the integration relay (IG2) (Click here).


  5. Click here

    REPLACE FUEL INJECTOR ASSEMBLYClick here

  6. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    REPLACE INTEGRATION RELAY

  8. Click here

    REPLACE ECMClick here

  9. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)