REMOTE CONTROL SWITCH ON-VEHICLE INSPECTION


  1. INSPECT REMOTE CONTROL SWITCH ASSEMBLY


    1. A015BN8

      Connect the remote control switch connector.

    2. A015BJS

      Turn the engine switch on (IG) and check that the power indicator light illuminates.

    3. Press the remote control switch, and check that the winch operates.

      Note

      Be careful not to tighten or strain the winch wire.

    4. Turn the engine switch off.

  2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. A01588F

      Remove the 3 bolts and screw.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.

  3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. A0159SG

      Remove the 3 bolts and 2 screws.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.

  4. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  5. REMOVE FRONT BUMPER WINCH COVER SUB-ASSEMBLY


    1. A0156DU

      Detach the 2 claws.

    2. Detach the 3 guides and remove front bumper winch cover sub-assembly.

  6. REMOVE RADIATOR GRILLE ASSEMBLY


    1. A0157G3E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the radiator grille assembly.

    2. Remove the 3 screws.

    3. Detach the 2 clips and 8 claws, and remove the radiator grille assembly.

    4. w/ Wide View Front Monitor System:


      1. Disconnect the connector.

  7. REMOVE FRONT BUMPER COVER


    1. Put protective tape around the bumper cover.

      A0156R5E01
      Text in Illustration
      *1 Protective Tape - -

    2. Using a T30 "TORX" socket, remove the 6 screws.

      A015DGIE01
      Text in Illustration
      *A LH Side *B RH Side

    3. Remove the 3 clips, 4 screws and 4 bolts.

    4. Detach the 10 claws.

      A0156KP

    5. Disconnect the winch control wire connector and remove the front bumper cover.

    6. w/ Fog Light:

      Disconnect the No. 4 engine room wire connector and remove the front bumper cover.

  8. INSPECT OVERHEAT TEMPERATURE INDICATOR


    1. A0156C3

      Remove the 4 screws and cover.

    2. A015BMX

      Disconnect the motor relay connector.

    3. A015AQC

      Remove the 2 nuts.

    4. Pull the bumper side winch control wire out of the bumper.

    5. Connect the bumper side winch control wire connector to the vehicle side winch control wire connector.

    6. Connect the bumper side winch control wire connector to the winch control switch connector.

    7. A0158VU

      Turn the engine switch on (IG) and check that the overheat temperature indicator light illuminates and the buzzer sounds.

    8. Turn the engine switch off.

    9. Disconnect the bumper side winch control wire connector from the winch control switch connector.

    10. Disconnect the bumper side winch control wire connector from the vehicle side winch control wire connector.

    11. Pass the bumper side winch control wire through the bumper.

    12. A015AQC

      Install the 2 nuts.

    13. A015BMX

      Connect the motor relay connector.

    14. A0156C3

      Install the cover with the 4 screws.

  9. INSTALL FRONT BUMPER COVER


    1. w/ Fog Light:

      Connect the No. 4 engine room wire connector.

    2. Connect the winch control wire connector and attach the 10 claws to install the front bumper cover.

    3. Install the 3 clips, 4 screws and 4 bolts.

    4. Using a T30 "TORX" socket, install the 6 screws.

  10. INSTALL RADIATOR GRILLE ASSEMBLY


    1. w/ Wide View Front Monitor System:


      1. Connect the connector.

    2. Attach the 2 clips and 8 claws to install the radiator grille assembly.

    3. Install the 3 screws.

  11. INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY

  12. INSTALL UPPER RADIATOR SUPPORT SEAL


    1. for Gasoline Engine:

      Install the upper radiator support seal Click here.

    2. for Diesel Engine:

      Install the upper radiator support seal (See page ).

  13. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Push in the clip to install the front fender splash shield sub-assembly RH.

    2. Install the 3 bolts and 2 screws.

  14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. Push in the clip to install the front fender splash shield sub-assembly LH.

    2. Install the 3 bolts and screw.