FRONT BUMPER (for Standard) INSTALLATION

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT UPPER CENTER BUMPER RETAINER


    1. Install the front upper center bumper retainer with the 3 bolts.

  2. INSTALL HEADLIGHT ASSEMBLY LH


    1. for Halogen Headlight:

      Click here

    2. for HID Headlight:

      Click here

  3. INSTALL HEADLIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  4. INSTALL FRONT BUMPER SIDE SUPPORT LH


    1. Attach the 3 clips to install the front bumper side support LH.

    2. Install the 2 screws.

  5. INSTALL FRONT BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


    1. Install the front No. 2 bumper extension sub-assembly LH with the 4 nuts.

      Torque:
      67 N*m  { 683 kgf*cm, 49 ft.*lbf }

  7. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. Install the front bumper reinforcement sub-assembly with the 6 nuts.

      Torque:
      71 N*m  { 724 kgf*cm, 52 ft.*lbf }

  9. INSTALL FRONT BUMPER ENERGY ABSORBER


    1. Install the front bumper energy absorber.

  10. INSTALL FRONT BUMPER COVER

    Tech Tips

    For the front bumper cover with garnish, use the procedure described below.


    1. A015BCT

      w/ Headlight Cleaner System:

      Connect the headlight cleaner hose.

    2. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:

      Connect the No. 4 engine room wire connector.

    3. Attach the 10 claws to install the front bumper cover.

    4. Install the 3 clips, 4 screws and 4 bolts.

    5. Using a T30 "TORX" socket, install the 6 screws.

  11. INSTALL RADIATOR GRILLE ASSEMBLY


    1. w/ Wide View Front Monitor System:


      1. Connect the connector.

    2. Attach the 2 clips and 8 claws to install the radiator grille assembly.

    3. Install the 3 screws.

  12. INSTALL UPPER RADIATOR SUPPORT SEAL


    1. Install the radiator support seal with the 7 clips.

      A015BVKE02

  13. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. Push in the clip to install the front fender splash shield sub-assembly LH.

    2. Install the 3 bolts and screw.

  14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Push in the clip to install the front fender splash shield sub-assembly RH.

    2. Install the 3 bolts and 2 screws.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for HID Headlight)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. ADJUST HEADLIGHT AIMING


    1. for Halogen Headlight:


      1. Click here

    2. for HID Headlight:


      1. Click here

  17. ADJUST FOG LIGHT AIMING (w/ Fog Light)

    Click here

  18. INSPECT TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ TOYOTA Parking Assist-sensor System)

    Click here