FRONT BUMPER (for Standard) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for HID Headlight)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. A01588F

      Remove the 3 bolts and screw.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.

  4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. A0159SG

      Remove the 3 bolts and 2 screws.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.

  5. REMOVE UPPER RADIATOR SUPPORT SEAL


    1. Remove the 7 clips and radiator support seal.

      A015BVKE02

  6. REMOVE RADIATOR GRILLE ASSEMBLY


    1. A0157G3E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the radiator grille assembly.

    2. Remove the 3 screws.

    3. Detach the 2 clips and 8 claws, and remove the radiator grille assembly.

    4. w/ Wide View Front Monitor System:


      1. Disconnect the connector.

  7. REMOVE FRONT BUMPER COVER

    Tech Tips

    For the front bumper cover with garnish, use the procedure described below.


    1. Put protective tape around the front bumper cover.

      A0155QIE01
      Text in Illustration
      *1 Protective Tape - -

    2. Using a T30 "TORX" socket, remove the 6 screws.

      A015DGIE01
      Text in Illustration
      *A LH Side *B RH Side

    3. Remove the 3 clips, 4 screws and 4 bolts.

    4. Detach the 10 claws and remove the front bumper cover.

      A0158BY

    5. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:

      Disconnect the No. 4 engine room wire connector and remove the front bumper cover.

    6. A0159AB

      w/ Headlight Cleaner System:

      Disconnect the headlight cleaner hose and remove the front bumper cover.

  8. REMOVE FRONT BUMPER ENERGY ABSORBER


    1. A015882

      Remove the front bumper energy absorber.

  9. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. A015DV1

      Remove the 6 nuts and front bumper reinforcement sub-assembly.

  10. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH


    1. A01584U

      Remove the 4 nuts and front No. 2 bumper extension sub-assembly LH.

  11. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT BUMPER SIDE SUPPORT LH


    1. A0158RA

      Remove the 2 screws.

    2. Detach the 3 clips and remove the front bumper side support LH.

  13. REMOVE FRONT BUMPER SIDE SUPPORT RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE HEADLIGHT ASSEMBLY LH


    1. for Halogen Headlight:

      Click here

    2. for HID Headlight:

      Click here

  15. REMOVE HEADLIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE FRONT UPPER CENTER BUMPER RETAINER


    1. A015C08

      Remove the 3 bolts and front upper center bumper retainer.