POWER MIRROR CONTROL SYSTEM (w/ Retract Mirror) Power Mirrors do not Return to Memorized Position

SYSTEM DESCRIPTION

When the seat memory switch 1, seat memory switch 2 or seat memory switch 3 is pressed, the position control ECU and switch mirror position signal is sent through the CAN communication line to the outer mirror control ECU. The outer mirror control ECU then activates the mirror control motors to move the mirrors to the previously recorded positions.

WIRING DIAGRAM

A0157MNE03

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC


    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK POWER MIRROR CONTROL FUNCTION


    1. Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

      OK
      Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

    NG

    PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)


    1. Check the Data List for proper functioning of the mirror position memory Click here.

      Mirror
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Mirror Memory No.1 Mirror position memorized in seat memory switch memory1 / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      Mirror Memory No.2 Mirror position memorized in seat memory switch memory2 / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      Mirror Memory No.3 Mirror position memorized in seat memory switch memory3 / ON or OFF

      ON: Memorized

      OFF: Not memorized

      		 -
      OK
      On tester screen, each item changes between ON and OFF according to above chart.

    NG

    REPLACE OUTER MIRROR CONTROL ECU Click here

    OK

  4. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)


    1. Check the Data List for proper functioning of the mirror position sensor Click here.

      Mirror
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      RH Mir Position Sensor V RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
      RH Mir Position Sensor H RH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
      LH Mir Position Sensor V LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
      LH Mir Position Sensor H LH side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
      OK
      When mirror control switch is operated, voltage changes within range shown in above chart.
      Result
      Result Proceed to
      LH side mirror does not operate normally A
      RH side mirror does not operate normally B
      Mirror operates normally C

    B

    CHECK OUTER MIRROR CONTROL ECU Click here

    C

    GO TO FRONT POWER SEAT CONTROL SYSTEM Click here

    A

  5. CHECK OUTER MIRROR CONTROL ECU

    A015A4TE54

    1. for LHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I18-2 (LVC) - I18-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-3 (LE1) - Body ground Always Below 1 Ω

    2. for RHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I24-2 (LVC) - I24-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I24-3 (LE1) - Body ground Always Below 1 Ω

    NG

    REPLACE OUTER MIRROR CONTROL ECU Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    1. A01577YE01

      for LHD:


      1. Disconnect the I18 ECU connector.

      2. Disconnect the I35 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-2 (LVC) - I35-10 (VC) Always Below 1 Ω
        I18-3 (LE1) - I35-21 (E1)
        I18-4 (VSR) - I35-22 (VSRL)
        I18-5 (HSRL) - I35-11 (HSRL)
        I35-10 (VC) - Body ground Always 10 kΩ or higher
        I35-21 (E1) - Body ground
        I35-22 (VSRL) - Body ground
        I35-11 (HSRL) - Body ground

    2. for RHD:


      1. Disconnect the I24 ECU connector.

      2. Disconnect the I35 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I24-2 (LVC) - I35-10 (VC) Always Below 1 Ω
        I24-3 (LE1) - I35-21 (E1)
        I24-4 (VSR) - I35-22 (VSRL)
        I24-5 (HSRL) - I35-11 (HSRL)
        I35-10 (VC) - Body ground Always 10 kΩ or higher
        I35-21 (E1) - Body ground
        I35-22 (VSRL) - Body ground
        I35-11 (HSRL) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

  7. CHECK OUTER MIRROR CONTROL ECU

    A015A4TE55

    1. for LHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I18-22 (RVC) - I18-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-23 (RE1) - Body ground Always Below 1 Ω

    2. for RHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I24-22 (RVC) - I24-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I24-23 (RE1) - Body ground Always Below 1 Ω

    NG

    REPLACE OUTER MIRROR CONTROL ECU Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    1. A01577YE05

      for LHD:


      1. Disconnect the I18 ECU connector.

      2. Disconnect the I32 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-22 (RVC) - I32-10 (VC) Always Below 1 Ω
        I18-23 (RE1) - I32-21 (E1)
        I18-24 (VSRR) - I32-22 (VSSR)
        I18-25 (HSRR) - I32-11 (HSSR)
        I32-10 (VC) - Body ground Always 10 kΩ or higher
        I32-21 (E1) - Body ground
        I32-22 (VSSR) - Body ground
        I32-11 (HSSR) - Body ground

    2. for RHD:


      1. Disconnect the I24 ECU connector.

      2. Disconnect the I32 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I24-22 (RVC) - I32-10 (VC) Always Below 1 Ω
        I24-23 (RE1) - I32-21 (E1)
        I24-24 (VSRR) - I32-22 (VSSR)
        I24-25 (HSRR) - I32-11 (HSSR)
        I32-10 (VC) - Body ground Always 10 kΩ or higher
        I32-21 (E1) - Body ground
        I32-22 (VSSR) - Body ground
        I32-11 (HSSR) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here