POWER MIRROR CONTROL SYSTEM (w/ Retract Mirror) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

SYSTEM DESCRIPTION

This circuit detects the conditions of the mirror retract switch.

The outer mirror switch sends information about the operating condition of the mirror retract switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU.

WIRING DIAGRAM

A015CV5E05

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC


    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. READ VALUE USING INTELLIGENT TESTER (MIRROR RETRACT SWITCH)


    1. Check the Data List for proper functioning of the mirror retract switch Click here.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Outer Mirror Fold SW Mirror retract switch signal / ON or OFF

      ON: Switch is on (retracting)

      OFF: Switch is off

      		 -
      OK
      On tester screen, each item changes between ON and OFF according to above chart.

    NG

    INSPECT RETRACTABLE OUTER MIRROR SWITCH Click here

    OK

  3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MIRROR RETRACT FUNCTION)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power mirror control function Click here.

      Mirror
      Tester Display Test Part Control Range Diagnostic Note
      Mirror Fold Mirror retract operation FOLD / OFF -
      Mirror Return Mirror retract operation RETURN / OFF -
      Result
      Result Proceed to
      Outer rear view mirror operates normally A
      Outer rear view mirror LH does not operate normally B
      Outer rear view mirror RH does not operate normally C

    B

    INSPECT OUTER MIRROR RETRACTOR LH Click here

    C

    INSPECT OUTER MIRROR RETRACTOR RH Click here

    A

    REPLACE OUTER MIRROR CONTROL ECU Click here

  4. INSPECT RETRACTABLE OUTER MIRROR SWITCH


    1. A015CI8E02

      Remove the switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      5 (E) - 6 (MR) Pressed (Retracts) Below 1 Ω
      Not pressed 10 kΩ or higher

    NG

    REPLACE RETRACTABLE OUTER MIRROR SWITCH Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND)


    1. A015DF4E01

      Disconnect the E2 ECU connector.

    2. Disconnect the G16 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E2-6 (RET) - G16-6 (MR) Always Below 1 Ω
      G16-5 (E) - Body ground
      G16-6 (MR) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

  6. INSPECT OUTER MIRROR RETRACTOR LH


    1. A015DD6E01

      Remove the mirror LH Click here.

    2. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      Note


      • Disconnect and reconnect the battery once between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      OK
      Measurement Condition Mirror Position Specified Condition

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Forward position (A) Moves from (A) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Forward position (A) Does not move

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Driving position (C) Moves from (C) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Driving position (C) Does not move

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Retracted position (E) Does not move

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Retracted position (E) Moves from (E) to driving position (C)

    NG

    REPLACE OUTER MIRROR RETRACTOR LH Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    1. A015D5JE05

      for LHD:


      1. Disconnect the I17 ECU connector.

      2. Disconnect the I35 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I17-1 (RL) - I35-19 (MR) Always Below 1 Ω
        I17-2 (FL) - I35-20 (MF)
        I35-19 (MR) - Body ground Always 10 kΩ or higher
        I35-20 (MF) - Body ground

    2. for RHD:


      1. Disconnect the I23 ECU connector.

      2. Disconnect the I35 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I23-1 (RL) - I35-19 (MR) Always Below 1 Ω
        I23-2 (FL) - I35-20 (MF)
        I35-19 (MR) - Body ground Always 10 kΩ or higher
        I35-20 (MF) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER MIRROR CONTROL ECU Click here

  8. INSPECT OUTER MIRROR RETRACTOR RH


    1. A015D48E01

      Remove the mirror RH Click here.

    2. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      Note


      • Disconnect and reconnect the battery once between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      OK
      Measurement Condition Mirror Position Specified Condition

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Forward position (A) Moves from (A) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Forward position (A) Does not move

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Driving position (C) Moves from (C) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Driving position (C) Does not move

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)

      Battery positive (+) → Terminal 19 (MR)

      Battery negative (-) → Terminal 20 (MF)

      		 Retracted position (E) Does not move

      Battery negative (-) → Terminal 19 (MR)

      Battery positive (+) → Terminal 20 (MF)

      		 Retracted position (E) Moves from (E) to driving position (C)

    NG

    REPLACE OUTER MIRROR RETRACTOR RH Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    1. A015D5JE06

      for LHD:


      1. Disconnect the I17 ECU connector.

      2. Disconnect the I32 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I17-5 (RR) - I32-19 (MR) Always Below 1 Ω
        I17-6 (FR) - I32-20 (MF)
        I32-19 (MR) - Body ground Always 10 kΩ or higher
        I32-20 (MF) - Body ground

    2. for RHD:


      1. Disconnect the I23 ECU connector.

      2. Disconnect the I32 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I23-5 (RR) - I32-19 (MR) Always Below 1 Ω
        I23-6 (FR) - I32-20 (MF)
        I32-19 (MR) - Body ground Always 10 kΩ or higher
        I32-20 (MF) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER MIRROR CONTROL ECU Click here