OUTER REAR VIEW MIRROR DISASSEMBLY

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE OUTER MIRROR LH

    A0159WS

    1. Push the upper part of the mirror surface and tilt it.

    2. Using a moulding remover, detach the 4 claws and separate the outer mirror LH from the mirror body.

      Tech Tips

      Apply protective tape to the outer rear mirror LH to prevent it from being damaged.

    3. A0155J8

      w/ EC Mirror:

      Disconnect the connector and remove the outer mirror LH.

    4. A0156WG

      w/ Mirror Heater:

      Disconnect the 2 connectors and remove the outer mirror LH.

  2. REMOVE OUTER MIRROR COVER

    A015B2GE02

    Tech Tips

    Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


    1. A015CDOE01
      Text in Illustration
      *1 Protective Tape

      Using 2 screwdrivers, detach the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

      Note

      Be careful not to break the ribs.

      Tech Tips

      Tape the screwdriver tip before use.

      A0158J0E01
      Text in Illustration
      *1 Protective Tape *2 Rib
      *a Inner Side of Outer Mirror Cover - -
    3. A015BJYE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

      Tech Tips

      Tape the moulding remover before use.

    4. Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

      Note

      Do not insert the moulding remover more than 4 mm (0.157 in.).

      Standard
      Area Specified Condition
      a 4mm
    5. A015AZHE01
      Text in Illustration
      *1 Protective Tape

      Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

      Note


      • Do not insert the moulding remover more than 4 mm (0.157 in.).

      • Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

      Standard
      Area Specified Condition
      a 40mm
      b 4mm

    6. Remove the moulding remover B.

    7. A015B57E02
      Text in Illustration
      *1 Protective Tape
      *a Lower Side

      Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

    8. Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

    9. A0155M1E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

    10. A0156EY

      Detach the 2 claws and remove the outer mirror cover.

      Note

      When removing the cover, be careful not to damage the side turn signal light assembly or cover.

  3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH


    1. A015ATN

      Remove the 3 screws and light.

    2. Disconnect the connector.

  4. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)


    1. Remove the gasket


      1. Remove the tape.

      2. A015DDF

        Detach the 9 guides and remove the gasket.

        Tech Tips

        Slightly lower the gasket so that the television camera assembly can be removed.

    2. Remove the lower mirror cover


      1. A015BZFE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver with its tip wrapped in protective tape, disconnect the 4 claws and remove the lower mirror cover.

    3. Remove the base


      1. Remove the wire harness.

      2. A015E09

        Using "TORX" socket wrench T25, remove the 3 screws.

        Note

        Make sure to replace the "TORX" screws with new ones.

      3. Disconnect the guide and remove the base.

    4. A015B1G

      Detach the connector from the wire clip.

    5. A015E0FE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disconnect the connector.

      Tech Tips

      Tape the moulding remover before use.

    6. Remove the body


      1. A0159WA

        Remove the 5 screws and body.

    7. Remove the body


      1. A015CJK

        Disconnect the 2 guides and remove the body.

        Note

        Be careful not to break the guide shown in the part of the illustration labeled A.

    8. A015AFD

      Remove the 3 screws and side television camera.