REAR DOOR DISASSEMBLY

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)


    1. A015950E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door outside moulding sub-assembly LH.

    2. A015DDJ

      Using a moulding remover, detach the 3 clamps and 7 clips, and remove the rear door outside moulding sub-assembly LH.

    3. Remove any clips remaining on the door panel.

      Note

      Be careful not to allow any clips or pieces of clips to fall inside the door panel.

  4. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    1. A015B9E

      Detach the claw.

    2. Remove the courtesy light and then disconnect the connector.

  5. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. A015B1YE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

      Tech Tips

      Tape the screwdriver tip before use.

  6. REMOVE REAR DOOR UPPER ARMREST BASE PANEL LH


    1. A015ALM

      Using a moulding remover, detach the 7 claws.

    2. Disconnect the connector and remove the armrest base panel.

  7. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A015DPX

      Detach the 2 claws and remove the regulator switch.

  8. REMOVE ASSIST GRIP COVER LH


    1. A015D94

      Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.

  9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A0155STE01

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tech Tips

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector and remove the rear door trim board sub-assembly LH.

    5. A0159D6

      Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

  10. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. A015864

      Detach the 4 clips and remove the rear inner door glass weatherstrip LH from the rear door trim board sub-assembly LH.

      Note


      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  11. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A0159ZD

      Detach the 2 claws and remove the rear door inside handle sub-assembly LH.

  12. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. A015C7U

      Remove the 6 screws and rear door inside handle bezel LH.

  13. REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 14 Speakers)


    1. A015AI1

      Disconnect the connector.

    2. Detach the clamp.

    3. Remove the 2 screws and speaker.

      Note

      Do not touch the cone part of the speaker.

  14. REMOVE REAR SPEAKER SET (w/ Rear Speaker)


    1. A0155P1

      Disconnect the speaker connector.

    2. Remove the 3 screws.

    3. Detach the claw and remove the speaker.

      Note

      Do not touch the cone part of the speaker.

  15. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A0158QNE01

      Using a clip remover, detach the 6 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the rear door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  16. REMOVE REAR DOOR PANEL PROTECTOR LH


    1. A0158MZ

      Detach the claw and remove the rear door panel protector LH.

  17. REMOVE REAR DOOR GLASS RUN LH


    1. A015C0T

      Remove the rear door glass run LH from the window frame.

  18. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    1. A0159WG

      Remove the 2 bolts.

    2. Remove the screw and rear door rear lower window frame sub-assembly LH.

  19. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A0157CH

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  20. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH


    1. Remove the rear door quarter window weatherstrip LH.

  21. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A0158QI

      Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

      Note

      Do not damage the door glass.

  22. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH (for Tempered Glass)


    1. A01566KE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the rear door glass channel sub-assembly LH.

      Note

      Be careful not to damage the door glass.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE REAR DOOR GLASS CHANNEL FILLER (for Tempered Glass)


    1. Remove the rear door glass channel filler.

  24. REMOVE REAR DOOR FRAME GARNISH LH


    1. A015BGT

      Detach the clip and remove the rear door frame garnish LH.

      Tech Tips

      This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish LH.

  25. REMOVE REAR NO. 2 DOOR FRAME GARNISH LH


    1. A015CDV

      Detach the clip and remove the rear No. 2 door frame garnish LH.

      Tech Tips

      This clip needs to be replaced with a new one because the clip will break when removing the rear No. 2 door frame garnish LH.

  26. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. A015C6NE05
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.

    2. Remove the 3 bolts and rear door window regulator sub-assembly LH.

      Note

      Be careful when removing the bolts as the motor may fall and become damaged.

    3. Remove the temporary bolt from the rear door window regulator sub-assembly LH.

  27. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A0155OZE01
      Text in Illustration
      *A for Models with Jam Protection Function on 4 Windows
      *B for Models with Jam Protection Function on Driver Door Window Only

      Using a T25 "TORX" driver, remove the 3 screws and motor.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.

  28. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    A0158QUE01

    1. Put protective tape around the belt moulding.

    2. A0158XC

      Detach the claw and remove the belt moulding.

  29. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

    A015D75E01

    1. Put protective tape around the window frame moulding.

    2. Detach the clip and remove the double-sided tape to remove the window frame moulding.

  30. REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

  31. REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. A0157TY

      Using a T30 ''TORX'' socket, remove the 3 screws and door lock.

      Note

      Be careful when removing the screws as the door lock may fall and become damaged.

  32. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A015BC1E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A0159Y6

      Remove the rear door lock remote control cable assembly LH.

  33. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A015948E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A015745E03
      Text in Illustration
      *A w/o Double Lock
      *B w/ Double Lock

      Remove the rear door inside locking cable assembly LH.

  34. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A0155MA

      Using a T30 ''TORX'' socket, loosen the screw.

    2. A015BF6

      Detach the claw and remove the rear door outside handle cover LH.

  35. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A015AWS

      Using a T30 "TORX" wrench, loosen the screw.

    2. w/ Entry and Start System:


      1. Disconnect the connector.

    3. A0158FY

      Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

  36. REMOVE REAR NO. 1 DOOR OUTSIDE HANDLE PAD LH


    1. A0155M4

      Detach the 3 claws and remove the rear No. 1 door outside handle pad LH.

  37. REMOVE REAR NO. 2 DOOR OUTSIDE HANDLE PAD LH


    1. A015760

      Detach the 2 claws and remove the rear No. 2 door outside handle pad LH.

  38. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A015D5M

      w/ Entry and Start System:


      1. Detach the clamp.

      2. Disconnect the connector.

    2. A01576Q

      Using a T30 ''TORX'' socket, loosen the screw.

    3. Slide the rear door outside handle frame sub-assembly LH and No. 4 electrical key wire harness to remove them.

      Tech Tips

      Remove the rear door outside handle frame sub-assembly LH through the service hole.

    4. Remove the lock open rod from the rear door outside handle frame sub-assembly LH.

  39. REMOVE NO. 4 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)


    1. A015B30

      Disconnect the connector.

    2. Detach the 2 clamps, and remove the No. 4 electrical key wire harness from the rear door outside handle frame sub-assembly LH.

  40. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)


    1. A015D1W

      Remove the screw and door electrical key oscillator.

  41. REMOVE REAR DOOR CHECK COVER LH (w/ Cover)


    1. A015CV8

      Remove the rear door check cover LH.

  42. REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. A015ARX

      Remove the bolt, 2 nuts and rear door check assembly LH.

      Note

      Be careful when removing the bolt and nuts as the rear door check assembly LH may fall and become damaged.

      Tech Tips

      Remove the rear door check assembly LH through the service hole.

  43. REMOVE REAR DOOR WEATHERSTRIP LH


    1. Detach the 21 clips and remove the rear door weatherstrip LH.

      A015CUEE01
      Text in Illustration
      *A w/ Spot Cover *B w/o Spot Cover
      *1 Double-sided Tape - -