SLIDING ROOF SYSTEM Sliding Roof Control Switch Circuit

DESCRIPTION

The sliding roof drive gear (sliding roof ECU) receives slide switch and tilt switch signals and drives its built-in motor.

WIRING DIAGRAM

A015C2KE01

INSPECTION PROCEDURE

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDING ROOF OPERATION)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down Click here.

      Sliding Roof
      Tester Display Test Part Control Range Diagnostic Note
      Slide Roof Operate sliding roof SLIDE CLOSE/TILT UP

      CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs

      OFF: Sliding roof is not operating

      		 Be careful to avoid injuries as this test causes vehicle parts to move.
      Slide Roof Operate sliding roof SLIDE OPEN/TILT DOWN

      OPEN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs

      OFF: Sliding roof is not operating

      		 Be careful to avoid injuries as this test causes vehicle parts to move.
      OK
      Sliding roof operates normally.

    NG

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF SWITCH)


    1. Use the Data List to check if the sliding roof switch is functioning properly Click here.

      Sliding Roof
      Item Measurement Item/Range Normal Condition Diagnostic Note
      Open Switch Sliding roof switch open signal/ON or OFF

      ON: OPEN switch is pressed

      OFF: OPEN switch is not pressed

      		 -
      Close Switch Sliding roof switch close signal/ON or OFF

      ON: CLOSE switch is pressed

      OFF: CLOSE switch is not pressed

      		 -
      Up Switch Sliding roof switch tilt up signal/ON or OFF

      ON: UP switch is pressed

      OFF: UP switch is not pressed

      		 -
      Down Switch Sliding roof switch tilt down signal/ON or OFF

      ON: DOWN switch is pressed

      OFF: DOWN switch is not pressed

      		 -
      OK
      When the switch is operating, the intelligent tester should display as shown in the table.

    NG

    INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) Click here

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) Click here

  3. INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

    A01563PE01

    1. Remove the map light Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      19 (UP) - 17 (GND9) UP switch is pressed Below 1 Ω
      19 (UP) - 17 (GND9) UP switch is not pressed 10 kΩ or higher
      18 (DOWN) - 17 (GND9) DOWN switch is pressed Below 1 Ω
      18 (DOWN) - 17 (GND9) DOWN switch is not pressed 10 kΩ or higher
      8 (OPN) - 17 (GND9) OPEN switch is pressed Below 1 Ω
      8 (OPN) - 17 (GND9) OPEN switch is not pressed 10 kΩ or higher
      7 (CLS) - 17 (GND9) CLOSE switch is pressed Below 1 Ω
      7 (CLS) - 17 (GND9) CLOSE switch is not pressed 10 kΩ or higher

    NG

    REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)

    A0155F7E01

    1. Disconnect the R5 drive gear connector.

    2. Disconnect the R7 map light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R5-10 (UP) - R7-19 (UP) Always Below 1 Ω
      R5-8 (DWN) - R7-18 (DOWN) Always Below 1 Ω
      R5-7 (OPN) - R7-8 (OPN) Always Below 1 Ω
      R5-9 (CLS) - R7-7 (CLS) Always Below 1 Ω
      R7-17 (GND9) - Body ground Always Below 1 Ω
      R5-2 (E) - Body ground Always Below 1 Ω
      R5-10 (UP) or R7-19 (UP) - Body ground Always 10 kΩ or higher
      R5-8 (DWN) or R7-18 (DOWN) - Body ground Always 10 kΩ or higher
      R5-7 (OPN) or R7-8 (OPN) - Body ground Always 10 kΩ or higher
      R5-9 (CLS) or R7-7 (CLS) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) Click here