POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. Apply MP grease to the sliding and rotating areas of the regulator motor.

    2. Using a T25 "TORX" driver, install the motor with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new rear window regulator motor uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A015C6NE04
      Text in Illustration
      *1 Temporary Bolt

      Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.

    2. Loosely install the temporary bolt onto the rear door window regulator sub-assembly LH.

    3. Insert the rear door window regulator sub-assembly LH into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly LH on the door panel.

      Note

      Be careful not to drop the rear door window regulator sub-assembly LH as it may become damaged.

    4. Temporarily install the rear door window regulator sub-assembly LH with the 3 bolts.

    5. Tighten the 4 bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A01572Z

      Slide the rear door glass sub-assembly LH as shown in the illustration to install it.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. A0158VK

      Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. Install the rear door rear lower window frame sub-assembly LH with the 2 bolts and screw.

  6. INSTALL REAR DOOR GLASS RUN


    1. Install the rear door glass run LH.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the door.

    2. A015AG6

      Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

      Note


      • When installing the rear door service hole cover LH, pull the links and connectors through the rear door service hole cover LH.

      • There should be no wrinkles or folds after attaching the rear door service hole cover LH.

      • After attaching the rear door service hole cover LH, check the sealing quality.

    3. Connect the 2 connectors.

    4. Attach the 6 clamps.

    5. A015BL3E01

      Install the bolt as shown in the illustration.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

  8. INSTALL REAR SPEAKER SET (w/ Rear Speaker)


    1. A0155P1

      Temporarily install the speaker by attaching the claw of the speaker to the door panel.

    2. Install the speaker with the 3 screws.

      Note

      Do not touch the cone part of the speaker.

    3. Connect the connector.

  9. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP


    1. A015905E02

      Install the rear inner door glass weatherstrip LH to the door panel.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. Connect the connector.

    2. A0157I9

      Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH to the rear door inside handle sub-assembly LH.

    3. A015D8Q

      Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly LH.

    4. Install the 3 screws.

  11. INSTALL ASSIST GRIP COVER


    1. Attach the 9 claws to install the assist grip cover LH to the rear door trim board sub-assembly LH.

  12. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY


    1. Connect the connector.

    2. A01561H

      Attach the 7 claws to install the armrest base panel.

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL


    1. Attach the 4 claws to install the rear door inside handle bezel LH.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.