Click here

ROOF HEADLINING (w/ Sliding Roof) REMOVAL

Click here
Click here Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)


    1. Remove the rear No. 2 seat assembly LH (Click here).

  4. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

    Tip:

    Use the same procedures described for the LH side.

  5. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)


    1. Remove the rear No. 2 seat assembly LH (Click here).

  6. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

    Tip:

    Use the same procedures described for the LH side.

  7. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH


    1. Detach the 7 claws and 4 clips, and remove the scuff plate.

  8. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedures described for the LH side.

  9. Click here

    REMOVE REAR STEP COVER

    Tip:

    Use the same procedure to remove the step cover on the other side.


    1. Detach the 2 claws and remove the step cover.

  10. Click here

    REMOVE REAR DOOR SCUFF PLATE LH


    1. Remove the screw.

    2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  11. Click here

    REMOVE REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedures described for the LH side.

  12. Click here

    REMOVE REAR FLOOR MAT REAR SUPPORT PLATE


    1. Detach the 6 clips and remove the support plate.

  13. Click here

    REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

    Tip:

    Use the same procedure to remove the front assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. A0156G7

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the front assist grip.

  14. Click here

    REMOVE FRONT PILLAR GARNISH LH


    1. Detach the clip 3 guides, and remove the front pillar garnish.

    2. for 9, 14 Speakers:

      Disconnect the speaker connector and then remove the front pillar garnish.

    3. A015CWJE01

      Protect the curtain shield airbag.


      1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

        Note:

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  15. Click here

    REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedures described for the LH side.

  16. Click here

    REMOVE CENTER PILLAR GARNISH COVER LH

    Tip:

    • for Manual Seat:

      When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. A015AD3

      Detach the 2 clips and 2 guides, and remove the cover.

  17. Click here

    REMOVE CENTER PILLAR GARNISH COVER RH

    Tip:

    Use the same procedures described for the LH side.

  18. Click here

    REMOVE CENTER LOWER PILLAR GARNISH LH

    Tip:

    • for Manual Seat:

      When removing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. A0158WN

      Remove the bolt and seat belt anchor.

    2. A0155QQ

      Detach the 2 claws and 7 clips, and remove the center lower pillar garnish.

  19. Click here

    REMOVE CENTER LOWER PILLAR GARNISH RH

    Tip:

    Use the same procedures described for the LH side.

  20. Click here

    REMOVE REAR ASSIST GRIP ASSEMBLY

    Tip:

    Use the same procedure to remove the rear assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. A015DJ8

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip.

  21. Click here

    REMOVE CENTER PILLAR GARNISH LH


    1. Remove the bolt.

    2. Detach the 2 clips and 2 guides.

    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish.

  22. Click here

    REMOVE CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedures described for the LH side.

  23. Click here

    REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tip:

    Use the same procedure to remove the rear seat cover cap on the other side.


    1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

      Tip:

      Tape the screwdriver tip before use.

  24. Click here

    REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    Tip:

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. A0158A5

      Detach the 3 claws and remove the cover.

    2. A015CT4

      Remove the bolt and rear No. 1 seat belt anchor.

    3. A0156NH

      w/ Rear No. 2 Seat, except Face to Face Seat Type:

      Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 18 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

      4. A0157GF

        w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. A0158HZ

        Detach the 18 clips and 2 claws, and remove the quarter trim panel.

  25. Click here

    REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tip:

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. A0157CJ

      Detach the 3 claws and remove the cover.

    2. A015CPR

      Remove the bolt and rear No. 1 seat belt anchor.

    3. A015DRR

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Detach the 3 claws and remove the cover.

      2. A015C42

        Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 16 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

      4. A0156CN

        w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. A0157MJ

        Detach the 16 clips and 2 claws, and remove the quarter trim panel.

  26. Click here

    REMOVE REAR FRONT QUARTER TRIM GARNISH LH


    1. Remove the screw.

    2. Detach the clip and 2 guides.

    3. Pass the seat belt anchor through the quarter trim garnish, and remove the quarter trim garnish.

  27. Click here

    REMOVE REAR FRONT QUARTER TRIM GARNISH RH

    Tip:

    Use the same procedures described for the LH side.

  28. Click here

    REMOVE REAR UPPER PILLAR GARNISH LH


    1. A015BNQE01

      w/ Rear No. 2 Seat, except Face to Face Seat Type


      1. Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

        Tip:

        Tape the screwdriver tip before use.

      2. A015D6A

        Remove the bolt and seat belt shoulder anchor.

    2. A0156T6

      Detach the 5 clips and remove the rear upper pillar garnish.

  29. Click here

    REMOVE CENTER BACK DOOR GARNISH (w/ Power Back Door)


    1. A015C1G

      Detach the 5 clips and 4 claws, and remove the center back door garnish.

  30. Click here

    REMOVE BACK DOOR SIDE GARNISH RH (w/ Power Back Door)


    1. w/o Power Back Door:

      Tip:

      Use the same procedure described for the LH side.

    2. A0159ZC

      w/ Power Back Door:


      1. Detach the clip and 4 claws, and remove the back door side garnish RH.

  31. Click here

    REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)


    1. A0156OJE01

      Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.

      Table 1. Text in Illustration
      *1 Power Back Door Rod
      *2 Hole of Back Door Service Hole Cover RH
      *a Back Door is Half-open
    2. A015A21

      Detach the 2 clips and separate the back door service hole cover RH, passing the power back door rod through the hole of the back door service hole cover RH.

      Note:

      If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover RH, so do not perform this operation with the back door in a fully open position.

      Tip:

      If any of the clips have remained on the back door, remove the clips from the back door and install them to the back door service hole cover RH.

    3. A0158LJ

      Remove the ball joint bolt, power back door rod and back door stay plate.

    4. Remove the back door service hole cover RH from the power back door rod.

  32. Click here

    REMOVE REAR UPPER PILLAR GARNISH RH


    1. Using a moulding remover, detach the 2 claws and open the seat belt shoulder anchor cover.

    2. A0159LR

      Remove the bolt and seat belt shoulder anchor.

    3. A0159J7

      w/o Power Back Door:


      1. Detach the 5 clips and remove the rear upper pillar garnish.

    4. A0158B7E02

      w/ Power Back Door:


      1. Detach the 5 clips.

      2. Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish.

  33. Click here

    REMOVE MAP LIGHT ASSEMBLY


    1. Using a screwdriver, detach the 2 claws and open the 2 covers.

      Tip:

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. Detach the 2 clips and 2 guides.

    4. A0159OKE01

      Disconnect the connector and then remove the map light.

  34. Click here

    REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. Detach the 4 clips.

    2. Disconnect the connector and then remove the room light.

  35. Click here

    REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. Using a screwdriver, detach the 4 claws and remove the room light lens.

      Tip:

      Tape the screwdriver tip before use.

    2. A015E5H

      Remove the 2 covers.

    3. A015AZOE01

      Using a screwdriver, push the 2 levers in the direction of the arrows in the illustration, and detach the 2 claws labeled A.

    4. Detach the 2 claws labeled B.

    5. A015ADFE01

      Detach the 4 claws and remove the room light from the room light switch base.

  36. Click here

    REMOVE VISOR BRACKET COVER

    Tip:

    Use the same procedure to remove the visor bracket cover on the other side.


    1. Detach the 4 claws and remove the visor bracket cover.

  37. Click here

    REMOVE VISOR ASSEMBLY LH


    1. Remove the 2 screws and visor.

  38. Click here

    REMOVE VISOR ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  39. Click here

    REMOVE VISOR HOLDER

    Tip:

    Use the same procedure to remove the visor holder on the other side.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  40. Click here

    REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)


    1. Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor.

      Tip:

      Tape the screwdriver tip before use.

  41. Click here

    REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

    Tip:

    Use the same procedures described for the LH side.

  42. Click here

    REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. Detach the 2 claws and remove the cover as shown in the illustration.

  43. Click here

    REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A015E20E01

      Slide the No. 2 cover in the direction of the arrow labeled (1).

    2. Pull the stopper in the direction of the arrow labeled (2) to remove the No. 2 cover.

  44. Click here

    REMOVE SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)


    1. Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.

  45. Click here

    REMOVE ASSIST GRIP ASSEMBLY

    Tip:

    Use the same procedure to remove the assist grip on the other side.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tip:

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  46. Click here

    REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

      Remove the No. 2 assist grip assembly.


      1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

        Tip:

        Tape the screwdriver tip before use.

      2. Detach the 2 clips and remove the assist grip.

      3. Remove the 2 clips from the vehicle body.

    2. A0156RKE01

      w/ Rear No. 2 Seat, for Face to Face Seat Type:

      Remove the No. 2 assist grip assembly.


      1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

        Tip:

        Tape the screwdriver tip before use.

      2. Detach the 2 clips and remove the assist grip.

      3. Remove the 2 clips from the vehicle body.

  47. Click here

    REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  48. Click here

    REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tip:

    Use the same procedure to remove the 3rd seat assist grip on the other side.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tip:

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  49. Click here

    REMOVE ROOF HEADLINING ASSEMBLY

    Tip:

    • for Manual Seat:

      When removing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.

    • for Power Seat:

      When removing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

    • for Power Seat:

      After moving the seats, disconnect the cable from the negative (-) battery terminal.


    1. A0157PK

      w/ EC Mirror:

      Disconnect the inner mirror connector.

    2. A0157NT

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A0157VM

      Disconnect the drive gear connector.

    4. A015C4JE01

      Disconnect the 3 roof wire connectors and washer hose.

    5. Detach the 4 clamps.

    6. A015BBSE01

      Remove the bolt.

    7. Disconnect the antenna cord connector and detach the 2 clamps.

    8. A0155BME01

      Disconnect the antenna cord connector.

    9. A015BAHE01

      Disconnect the washer hose.

    10. A01581WE01

      for 3 Person Seat Type Rear No. 2 Seat:

      Detach the 12 claws, 2 clips, 2 guides and 16 fasteners.

    11. A015DMQE01

      except 3 Person Seat Type Rear No. 2 Seat:

      Detach the 12 claws, 3 clips, 2 guides and 16 fasteners.

    12. A015D1H

      Remove the headlining from the rear of the vehicle as shown in the illustration.

      Note:

      Be careful not to damage the roof headlining when taking it out.

  50. Click here

    REMOVE FRONT ROOF SIDE RAIL GARNISH LH


    1. Detach the 3 clips.

    2. Cut off the 3 clips and remove the roof side rail garnish.

    3. Remove 3 clips from the vehicle body.

  51. Click here

    REMOVE FRONT ROOF SIDE RAIL GARNISH RH

    Tip:

    Use the same procedures described for the LH side.

  52. Click here

    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip.

  53. Click here

    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedures described for the LH side.

  54. Click here

    REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip.

  55. Click here

    REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedures described for the LH side.

  56. Click here

    REMOVE BACK DOOR WEATHERSTRIP


    1. Remove the back door weatherstrip.

  57. Click here

    REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH


    1. Put protective tape around the front door scuff plate outside.

    2. Detach the 4 clips and remove the front door scuff plate outside.

  58. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedures described for the LH side.

  59. Click here

    REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH


    1. Put protective tape around the rear door scuff plate outside.

    2. Detach the 3 clips and remove the rear door scuff plate outside.

  60. Click here

    REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tip:

    Use the same procedures described for the LH side.

  61. Click here

    REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Detach the 6 claws of the plate, and slide the plate in the direction of the arrow to remove it.

  62. Click here

    REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  63. Click here

    REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Detach the 6 claws and remove the plate.

  64. Click here

    REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  65. Click here

    REMOVE ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)


    1. Detach the 7 claws and remove the cover.

  66. Click here

    REMOVE ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tip:

    Use the same procedures described for the LH side.

  67. Click here

    REMOVE REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tip:

    Use the same procedure to remove the hanger on the other side.


    1. Remove the 2 spring nuts and hanger.

  68. Click here

    REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH


    1. Remove the 2 spring nuts and hanger.

  69. Click here

    REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH

    Tip:

    Use the same procedures described for the LH side.

  70. Click here

    REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH


    1. w/ Rear Heater:

      Remove the 8 screws and duct.

    2. A015B9H

      Remove the 7 screws.

    3. Detach the 4 claws and remove the quarter trim cover.

  71. Click here

    REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH


    1. Remove the 7 screws.

    2. Detach the 4 claws and remove the quarter trim cover.

  72. Click here

    REMOVE NO. 2 CUP HOLDER


    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the cup holder.

  73. Click here

    REMOVE NO. 1 CUP HOLDER


    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the cup holder.

  74. Click here

    REMOVE NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)


    1. Detach the 4 claws and remove the cover.

  75. Click here

    REMOVE NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)


    1. Remove the 6 screws and duct.

    2. A0156JZ

      Detach the 4 claws and remove the cover.

  76. Click here

    REMOVE NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)


    1. Detach the 4 claws and remove the cover.

  77. Click here

    REMOVE NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    Tip:

    Use the same procedures described for the LH side.

  78. Click here

    REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)


    1. Detach the 4 claws and remove the seat lock control lever.

  79. Click here

    REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tip:

    Use the same procedures described for the LH side.

  80. Click here

    REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)


    1. Detach the 6 clips and remove the rear No. 2 seat cover bezel.

  81. Click here

    REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tip:

    Use the same procedures described for the rear No. 2 seat cover bezel.

  82. Click here

    REMOVE QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)


    1. Detach the 6 clips and remove the quarter trim cover.

  83. Click here

    REMOVE QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    Tip:

    Use the same procedures described for the LH side.

  84. Click here

    REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH


    1. Remove the quarter trim lid.

  85. Click here

    REMOVE SIDE TRIM BOX COVER


    1. Remove the side trim box cover.

  86. Click here

    REMOVE SIDE TRIM BOX


    1. Remove the 9 screws and side trim box.

  87. Click here

    REMOVE NO. 2 MULTIPLEX NETWORK BODY ECU


    1. Disconnect the 2 connectors.

    2. Remove the bolt and multiplex network body ECU.