ENTRY AND START SYSTEM (for Entry Function) Room Oscillator does not Recognize Key

DESCRIPTION

If the room oscillator does not recognize the key, one of the following may be the cause: 1) communication between the indoor electrical key antenna (for Front) and electrical key transmitter cannot be performed; or 2) communication between the indoor electrical key antenna (for Rear 1) and electrical key transmitter cannot be performed; or 3) communication between the indoor electrical key antenna (for Rear 2) and electrical key transmitter cannot be performed.

WIRING DIAGRAM

A015A9BE05

INSPECTION PROCEDURE

Note


  • Before performing the inspection, check that there are no problems related to the "CAN Communication System" and "LIN Communication System".

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.

PROCEDURE


  1. CHECK ENTRY AND START SYSTEM (ENTRY FUNCTION)


    1. Check that the entry lock and unlock function can be operated at each door Click here.


    NG

    Go to DTC OF OTHER COMPONENTS (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR) Click here

    OK

  2. CHECK ENTRY AND START SYSTEM (START FUNCTION)


    1. A0158WKE01

      Remove the battery of the electrical key transmitter Click here.

    2. With the brake pedal depressed, touch the key to the engine switch, as shown in the illustration.

    3. When operating the engine switch, check whether the power source mode changes.

      OK
      Power source mode changes.

      Tech Tips


      • When the electrical key transmitter cannot be verified even though it is in the operating range of the start function, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter and holding the transmitter against the engine switch.

      • When performing the check, if the power source mode changes, there is a problem with key certification inside the cabin.


    NG

    Go to ENTRY AND START SYSTEM (Power Source Mode does not Change) Click here

    OK

  3. CHECK WAVE ENVIRONMENT


    1. Install the battery to the electrical key transmitter Click here.

    2. Bring the electrical key transmitter near the indoor electrical key antenna (in center console), and perform an engine control system start check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the center console, communication is not possible.

      OK
      Engine starts.

    3. Bring the electrical key transmitter near the indoor electrical key antenna (in rear No. 1 seat cushion), and perform an engine control system start check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the rear No. 1 seat cushion, communication is not possible.

      OK
      Engine starts.

    4. Bring the electrical key transmitter near the indoor electrical key antenna (in rear No. 2 seat cushion), and perform an engine control system start check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the rear No. 2 seat cushion, communication is not possible.

      Tech Tips


      • When the electrical key transmitter is brought near the indoor electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference, If installed, remove them and perform the operation check.

      OK
      Engine starts.

    NG

    KEY DIAGNOSTIC MODE Click here

    OK

    AFFECTED BY WAVE INTERFERENCE

  4. KEY DIAGNOSTIC MODE


    1. A0157Y9E01

      Diagnostic mode inspection (indoor electrical key antenna (for Front)).


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Front Room.

      5. When the electrical key transmitter is placed on the driver seat or front passenger seat cushion, check that the wireless door lock buzzer sounds.

    2. A0156RAE01

      Diagnostic mode inspection (indoor electrical key antenna (for Rear 1)).


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Rear Room.

      5. When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.

    3. A015811E01

      Diagnostic mode inspection (indoor electrical key antenna (for Rear 2)).


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Back Door (inside) Room.

      5. When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.

      Tech Tips


      • If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.

      • It is possible to check which indoor electrical key antenna (front, rear 1 or rear 2) is operating by sounding the buzzer.

      • If the buzzer does not sound for any indoor electrical key antennas, the certification ECU (smart key ECU assembly) circuit may have a malfunction.

      Result
      Result Proceed to
      Front operation check fails A
      Rear 1 operation check fails B
      Rear 2 operation check fails C
      Front, rear 1 and rear 2 operation checks are normal or fail D

    B

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA) Click here

    C

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA) Click here

    D

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    A

  5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

    A0157CYE08

    1. Disconnect the E29 ECU connector.

    2. Disconnect the V3 antenna connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      V3-1 (CLG3) - E29-11 (CLG5) Always Below 1 Ω
      V3-3 (CLGB) - E29-12 (CG5B) Always Below 1 Ω
      V3-1 (CLG3) - Body ground Always 10 kΩ or higher
      V3-3 (CLGB) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK INDOOR ELECTRICAL KEY ANTENNA (for Front Floor)

    A0157KBE07

    1. Measure the voltage according to the value(s) in the table below.

      OK
      Tester Connection Tool Setting Switch Condition Specified Condition
      E29-11 (CLG5) - E29-12 (CG5B) 2 V/DIV, 2 μsec./DIV. (Reference) Engine switch on (IG) Pulse generation

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Front Floor) Click here

  7. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

    A015BL2E01

    1. Disconnect the E29 ECU connector.

    2. Disconnect the L8 antenna connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L8-1 (CLG4) - E29-13 (CLG6) Always Below 1 Ω
      L8-2 (CLGB) - E29-14 (CG6B) Always Below 1 Ω
      L8-1 (CLG4) - Body ground Always 10 kΩ or higher
      L8-2 (CLGB) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor)

    A0157KBE08

    1. Measure the voltage according to the value(s) in the table below.

      OK
      Tester Connection Tool Setting Switch Condition Specified Condition
      E29-13 (CLG6) - E29-14 (CG6B) 2 V/DIV., 2 μsec./DIV. (Reference) Engine switch on (IG) Pulse generation

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Rear 1 Floor) Click here

  9. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - INDOOR ELECTRICAL KEY ANTENNA)

    A0157CYE09

    1. Disconnect the E29 ECU connector.

    2. Disconnect the L9 antenna connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L9-1 (CLG6) - E29-15 (CLG) Always Below 1 Ω
      L9-2 (CLGB) - E29-16 (CG7B) Always Below 1 Ω
      L9-1 (CLG6) - Body ground Always 10 kΩ or higher
      L9-2 (CLGB) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor)

    A0157KBE09

    1. Measure the voltage according to the value(s) in the table below.

      OK
      Tester Connection Tool Setting Switch Condition Specified Condition
      E29-15 (CLG7) - E29-16 (CG7B) 2 V/DIV., 2 μsec./DIV. (Reference) Engine switch on (IG) Pulse generation

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    REPLACE INDOOR ELECTRICAL KEY ANTENNA (for Rear 2 Floor) Click here