ENTRY AND START SYSTEM (for Entry Function) Front Passenger Side Door Entry Lock Function does not Operate

DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle (entry lock switch) → front passenger side door electrical key oscillator).

WIRING DIAGRAM

A015CNME06

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the master switch assembly door control switch is operated, check that the locked doors unlock.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door Lock Position SW Front passenger side door lock position switch signal / ON or OFF

      ON: Front passenger side door unlocked

      OFF: Front passenger side door locked

      		 -
      OK
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH)


    1. Using the intelligent tester, read the Data List.

      Entry & Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Trigger Switch Front passenger side door outside handle lock switch / ON or OFF

      ON: Entry lock switch pushed

      OFF: Entry lock switch not pushed

      		 -
      OK
      On tester screen, item changes between ON and OFF according to above chart.

    NG

    CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR) Click here

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)


    1. A01561EE52

      Disconnect the z22 or z24 oscillator connector.

    2. Disconnect the z21 or z23 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      z22-9 (TRG-) - z21-1 (TRG-) Always Below 1 Ω
      z22-9 (TRG-) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      z24-9 (TRG-) - z23-1 (TRG-) Always Below 1 Ω
      z24-9 (TRG-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE)


    1. A015CQYE04

      Disconnect the E29 ECU connector.

    2. Disconnect the z21 or z23 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E29-4 (TSW2) - z21-3 (TRG+) Always Below 1 Ω
      E29-4 (TSW2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      E29-4 (TSW2) - z23-3 (TRG+) Always Below 1 Ω
      E29-4 (TSW2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT FRONT DOOR OUTSIDE HANDLE (for Front Passenger Side)


    1. A015B3ME01

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Switch Condition Specified Condition
      z21-1 (TRG-) - z21-3 (TRG+) Lock switch not pushed 10 kΩ or higher
      Lock switch pushed Below 1 Ω
      for RHD
      Tester Connection Switch Condition Specified Condition
      z23-1 (TRG-) - z23-3 (TRG+) Lock switch not pushed 10 kΩ or higher
      Lock switch pushed Below 1 Ω

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE Click here

    OK

  7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR


    1. Replace the door electrical key oscillator Click here.


    NEXT

  8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)


    1. Check that the entry function operates normally.

      OK
      Operates normally.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (DOOR ELECTRICAL OSCILLATOR IS DEFECTIVE)