ENTRY AND START SYSTEM (for Entry Function) Front Passenger Side Door Entry Unlock Function does not Operate

DESCRIPTION

If the front passenger side door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be a touch sensor circuit (certification ECU (smart key ECU assembly) → front passenger side door outside handle → front passenger side door electrical key oscillator).

WIRING DIAGRAM

A015DHRE06

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the master switch assembly door control switch is operated, check that the locked doors unlock.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door Lock Position SW Front passenger side door lock position switch signal / ON or OFF

      ON: Front passenger side door unlocked

      OFF: Front passenger side door locked

      		 -
      OK
      On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR)


    1. Using the intelligent tester, read the Data List.

      Entry & Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Touch Sensor Front passenger side door touch sensor / ON or OFF

      ON: Touch sensor touched

      OFF: Touch sensor not touched

      		 -
      OK
      "ON" (sensor is touched) and "OFF" (sensor is not touched) appears on the screen.

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR) Click here

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)


    1. A01565RE06

      Disconnect the E29 ECU connector.

    2. Disconnect the z22 or z24 oscillator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      E29-6 (SEL2) - z22-4 (SEL) Always Below 1 Ω
      E29-23 (SEN2) - z22-6 (SENS) Always Below 1 Ω
      E29-6 (SEL2) - Body ground Always 10 kΩ or higher
      E29-23 (SEN2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      E29-6 (SEL2) - z24-4 (SEL) Always Below 1 Ω
      E29-23 (SEN2) - z24-6 (SENS) Always Below 1 Ω
      E29-6 (SEL2) - Body ground Always 10 kΩ or higher
      E29-23 (SEN2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)


    1. A01561EE56

      Disconnect the z21 or z23 handle connector.

    2. Disconnect the z22 or z24 oscillator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      z21-6 (SGT) - z22-2 (SGT) Always Below 1 Ω
      z21-6 (SGT) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      z23-6 (SGT) - z24-2 (SGT) Always Below 1 Ω
      z23-6 (SGT) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. REPLACE DOOR ELECTRICAL KEY OSCILLATOR


    1. Replace the door electrical key oscillator Click here.


    NEXT

  7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)


    1. Check that the entry function operates normally.

      OK
      Operates normally.

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE Click here

    OK

    END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

  8. REPLACE FRONT DOOR OUTSIDE HANDLE


    1. Replace the front door outside handle Click here.


    NEXT

  9. CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)


    1. Check that the entry function operates normally.

      OK
      Operates normally.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)