Click here

BACK DOOR LOCK INSPECTION

Click here
Click here Click here
  1. Click here

    INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

    Table 1. Text in Illustration
    *1 Full-latch *2 Open-latch
    *a

    Component without harness connected

    (Back Door Lock assembly)

    		 - -

    1. Set the back door lock to the full-latch position.

    2. Apply battery voltage to the door motor connector and check the operation of the door lock motor.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → 2 (ACT+)

      Battery negative (-) → 1 (ACT-)

      		 Moves to open-latch position

      • If the result is not as specified, replace the back door lock assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (ACT-) - 3 (+) Open-latch Below 1 Ω
      1 (ACT-) - 3 (+) Full-latch 10 kΩ or higher

      • If the result is not as specified, replace the back door lock assembly.

  2. Click here

    INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)


    1. A0158YZE01

      Inspect the closer motor operation.


      1. Set the back door lock assembly to the full-latch position.

      2. Apply battery voltage and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 1 (M+)

        Battery negative (-) → 2 (M-)

        		 Moves to open-latch position

        • If the result is not as specified, replace the back door lock assembly.

      3. Set the back door lock assembly to the half-latch position.

      4. Apply battery voltage and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 2 (M-)

        Battery negative (-) → 1 (M+)

        		 Moves to over-latch position

        • If the result is not as specified, replace the back door lock assembly.

          Table 2. Text in Illustration
          *1 Release
          *2 Close
          *3 Drive Gear
          *4 Over-latch
          *5 Full-latch
          *6 Half-latch
          *7 Open-latch
          *a

          Component without harness connected

          (Back Door Lock Assembly)
    2. A015DAQE01

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 3. Half-latch Switch
      Tester Connection Condition Specified Condition
      5 (CLS) - 4 (E) Over-latch Below 1 Ω
      Full-latch 10 kΩ or higher
      Half-latch 10 kΩ or higher
      Open-latch Below 1 Ω

      • If the result is not as specified, replace the back door lock assembly.

        Closer Position Switch
        Tester Connection Condition Specified Condition
        6 (OPN) - 4 (E) Selector gear is in center position Below 1 Ω
        Selector gear is not in center position 10 kΩ or higher

      • If the result is not as specified, replace the back door lock assembly.

      Back Door Courtesy Switch
      Tester Connection Condition Specified Condition
      3 (CTY) - 4 (E)

      Half-latch

      Open-latch

      		 Below 1 Ω

      Over-latch

      Full-latch

      		 10 kΩ or higher

      • If the result is not as specified, replace the back door lock assembly.

        Table 4. Text in Illustration
        *1 Release
        *2 Close
        *3 Closer Position Switch
        *4 Selector Gear
        *5 Drive Gear
        *6 Over-latch
        *7 Full-latch
        *8 Half-latch
        *9 Open-latch
        *a

        Component without harness connected

        (Back Door Lock Assembly)