CAN COMMUNICATION SYSTEM (for RHD) Open in CAN Main Wire

DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.

  • CAN main wire and connector

  • No. 1 junction connector

  • No. 2 junction connector

  • No. 3 junction connector

  • ECM

  • Combination meter assembly

  • DLC3 CAN branch wire or connector

WIRING DIAGRAM

A0156CQE02

INSPECTION PROCEDURE

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.


    NEXT

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      For vehicles with an SRS system:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  3. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DLC3)


    1. A0157YPE05
      Text in Illustration
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω

      Note

      When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" Click here after repairing the trouble area.


    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    OK

  4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    1. A0155I5E13
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the E69 No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-4 (CANH) - E69-15 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A0155I5E12
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-1 (CANH) - E69-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 2 JUNCTION CONNECTOR

  6. CONNECT CONNECTOR


    1. Reconnect the E69 No. 2 junction connector.


    NEXT

  7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A0155I5E14
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the E72 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-2 (CANH) - E72-13 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A0155I5E15
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-1 (CANH) - E72-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

    REPLACE NO. 1 JUNCTION CONNECTOR

  9. CONNECT CONNECTOR


    1. Reconnect the E72 No. 1 junction connector.


    NEXT

  10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 1 JUNCTION CONNECTOR)


    1. A01580GE03
      Text in Illustration
      *A except 1VD-FTV
      *B for 1VD-FTV
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the A52 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      except 1VD-FTV
      Tester Connection Switch Condition Specified Condition
      A52-10 (CANH) - A52-11 (CANL) Ignition switch off 108 to 132 Ω
      for 1VD-FTV
      Tester Connection Switch Condition Specified Condition
      A52-41 (CANH) - A52-49 (CANL) Ignition switch off 108 to 132 Ω
      Result
      Result Proceed to
      OK (for 1GR-FE) A
      OK (for 1UR-FE) B
      OK (for 1VD-FTV) C
      NG D

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 1 JUNCTION CONNECTOR)

    A

    REPLACE ECM Click here

  11. CONNECT CONNECTOR


    1. Reconnect the E69 No. 2 junction connector.


    NEXT

  12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A0155I5E16
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E75 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-3 (CANH) - E75-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A0155I5E17
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-1 (CANH) - E75-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

    REPLACE NO. 3 JUNCTION CONNECTOR

  14. CONNECT CONNECTOR


    1. Reconnect the E75 No. 3 junction connector.


    NEXT

  15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)


    1. A0156A9E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the E7 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E7-25 (CANH) - E7-26 (CANL) Ignition switch off 108 to 132 Ω
      Result
      Result Proceed to
      OK (w/ Multi-information Display) A
      OK (w/o Multi-information Display) B
      NG C

    B

    REPLACE COMBINATION METER ASSEMBLY Click here

    C

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)

    A

    REPLACE COMBINATION METER ASSEMBLY Click here