Click here

CAN COMMUNICATION SYSTEM (for RHD) Air Conditioning Amplifier Communication Stop Mode

Click here
Click here Click here
DTC Code DTC Name
  Air Conditioning Amplifier Communication Stop Mode
Click here

DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode

Either condition is met:


  • "Air Conditioning Amplifier" is not displayed on "Bus Check".

  • "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" applies.

  • Power source or inside air conditioning amplifier assembly

  • Air conditioning amplifier assembly

  • Air conditioning amplifier assembly CAN branch wire or connector
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      For vehicle with an SRS system:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


  3. Click here

    CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)


    1. A0159DCE02

      Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.


      • *1: w/ Rear Air Conditioning System

      • *2: w/o Rear Air Conditioning System

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 1. w/ Rear Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      E35-3 (CANH) - E35-4 (CANL) Ignition switch off 54 to 69 Ω
      Table 2. w/o Rear Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      E81-11 (CANH) - E81-12 (CANL) Ignition switch off 54 to 69 Ω
      Table 3. Text in Illustration
      *A w/ Rear Air Conditioning System
      *B w/o Rear Air Conditioning System
      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

  4. Click here

    CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)


    1. A015CIFE01

      Connect the cable to the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    2. Disconnect the E36*1 or E81*2 air conditioning amplifier assembly connector.


      • *1: w/ Rear Air Conditioning System

      • *2: w/o Rear Air Conditioning System

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 4. w/ Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E36-1 (GND) - Body ground Always Below 1 Ω
      E36-2 (E1) - Body ground Always Below 1 Ω
      Table 5. w/o Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E81-14 (GND) - Body ground Always Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Table 6. w/ Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E36-6 (+B1) - Body ground Always 11 to 14 V
      E36-7 (+B2) - Body ground Always 11 to 14 V
      E36-5 (IG+) - Body ground Ignition switch ON 11 to 14 V
      Table 7. w/o Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E81-21 (+B1) - Body ground Always 11 to 14 V
      E81-1 (IG+) - Body ground Ignition switch ON 11 to 14 V
      Table 8. Text in Illustration
      *A w/ Rear Air Conditioning System
      *B w/o Rear Air Conditioning System
      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

  5. Click here

    REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

  6. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLYClick here