CAN COMMUNICATION SYSTEM (for LHD) Short in CAN Bus Lines

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

  • Short between CAN bus lines

  • ECM

  • Center airbag sensor assembly*1

  • Headlight swivel ECU assembly*2

  • Multi-media module receiver assembly*3

  • Air conditioning amplifier assembly

  • Main body ECU (cowl side junction block LH)

  • Network gateway ECU*4

  • Combination meter assembly

  • 4WD control ECU*5

  • Clearance warning ECU assembly*5, *6

  • Master cylinder solenoid (skid control ECU)*5

  • No. 1 junction connector

  • No. 2 junction connector

  • No. 3 junction connector

  • No. 6 junction connector*5

WIRING DIAGRAM

A015CEHE01
A015DJ6E01
A0157SDE01
A015DARE01

INSPECTION PROCEDURE

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.


    NEXT

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      For vehicles with an SRS system:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  3. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)


    1. A0157YPE06
      Text in Illustration
      *a Front view of DLC3

      Disconnect the E75 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    OK

  4. CONNECT CONNECTOR


    1. Reconnect the E75 No. 3 junction connector.


    NEXT

  5. SYSTEM CHECK


    1. Check the vehicle specifications.

      Result
      Result Proceed to
      w/ Network Gateway ECU A
      w/o Network Gateway ECU B

    B

    CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE) Click here

    A

  6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)


    1. A0157YPE06
      Text in Illustration
      *a Front view of DLC3

      Disconnect the E72 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

    Note

    For vehicles without dynamic headlight auto leveling, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Center Airbag Sensor Assembly)".


    1. A0155I5E20
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-3 (CANH) - E72-14 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY) Click here

    OK

  8. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    1. A0155I5E21
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-4 (CANH) - E72-15 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY) Click here

    OK

  9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A0155I5E22
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-2 (CANH) - E72-13 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (ECM) Click here

    OK

    REPLACE NO. 1 JUNCTION CONNECTOR

  10. CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)


    1. A0155I5E20
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the E101 headlight swivel ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-3 (CANH) - E72-14 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (MPX1, MPX2)

    OK

    REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY Click here

  11. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)


    1. A0155I5E21
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the E47 center airbag sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-4 (CANH) - E72-15 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

  12. CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    1. A0155I5E22
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the A38 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-2 (CANH) - E72-13 (CANL) Ignition switch off 1 MΩ or higher
      Result
      Result Proceed to
      OK (for 1GR-FE) A
      OK (for 1UR-FE) B
      OK (for 3UR-FE) C
      OK (for 1VD-FTV) D
      NG E

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPLACE ECM Click here

    E

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

    A

    REPLACE ECM Click here

  13. CONNECT CONNECTOR


    1. Reconnect the E72 No. 1 junction connector.


    NEXT

  14. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A0155I5E23
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the E69 No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-1 (CANH) - E69-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

    OK

  15. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)


    1. A0157YPE06
      Text in Illustration
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  16. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

    Note

    For vehicles without a navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier Assembly)".


    1. A0155I5E24
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-2 (CANH) - E69-13 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY) Click here

    OK

  17. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A0155I5E25
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-5 (CANH) - E69-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY) Click here

    OK

  18. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)


    1. A0155I5E26
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-3 (CANH) - E69-14 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU) Click here

    OK

    REPLACE NO. 2 JUNCTION CONNECTOR

  19. CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)


    1. A0155I5E24
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the F77 multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-2 (CANH) - E69-13 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

  20. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A0155I5E25
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.

      *1: w/ Rear Air Conditioning System

      *2: w/o Rear Air Conditioning System

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-5 (CANH) - E69-16 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  21. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)


    1. A0155I5E26
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the E31 network gateway ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-3 (CANH) - E69-14 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)

    OK

    REPLACE NETWORK GATEWAY ECU Click here

  22. CONNECT CONNECTOR


    1. Reconnect the E69 No. 2 junction connector.


    NEXT

  23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A0155I5E27
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E75 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-1 (CANH) - E75-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

  24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    1. A0155I5E28
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-4 (CANH) - E75-15 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) Click here

    OK

  25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A0155I5E29
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-3 (CANH) - E75-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY) Click here

    OK

    REPLACE NO. 3 JUNCTION CONNECTOR

  26. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    1. A0155I5E28
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E3 main body ECU (cowl side junction block LH) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-4 (CANH) - E75-15 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

  27. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    1. A0155I5E29
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E7 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-3 (CANH) - E75-14 (CANL) Ignition switch off 1 MΩ or higher
      Result
      Result Proceed to
      OK (w/ Multi-information Display) A
      OK (w/o Multi-information Display) B
      NG C

    B

    REPLACE COMBINATION METER ASSEMBLY Click here

    C

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

    A

    REPLACE COMBINATION METER ASSEMBLY Click here

  28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)


    1. A0157YPE06
      Text in Illustration
      *a Front view of DLC3

      Disconnect the E72 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

    Note

    For vehicles without an airbag system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - 4WD Control ECU)".


    1. A0155I5E21
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-4 (CANH) - E72-15 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY) Click here

    OK

  30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)


    1. A0155I5E30
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-5 (CANH) - E72-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU) Click here

    OK

  31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A0155I5E22
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-2 (CANH) - E72-13 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (ECM) Click here

    OK

    REPLACE NO. 1 JUNCTION CONNECTOR

  32. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)


    1. A0155I5E21
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the E47 center airbag sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-4 (CANH) - E72-15 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

  33. CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)


    1. A0155I5E30
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the A27 4WD control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-5 (CANH) - E72-16 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)

    OK

    REPLACE 4WD CONTROL ECU Click here

  34. CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    1. A0155I5E22
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Disconnect the A38 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E72-2 (CANH) - E72-13 (CANL) Ignition switch off 1 MΩ or higher
      Result
      Result Proceed to
      OK (for 1GR-FE) A
      OK (for 1UZ-FE) B
      OK (for 1VD-FTV) C
      NG D

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

    A

    REPLACE ECM Click here

  35. CONNECT CONNECTOR


    1. Reconnect the E72 No. 1 junction connector.


    NEXT

  36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A0155I5E23
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the E69 No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-1 (CANH) - E69-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

    OK

  37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)


    1. A0157YPE06
      Text in Illustration
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  38. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

    Note

    For vehicles without a navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier)".


    1. A0155I5E24
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-2 (CANH) - E69-13 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY) Click here

    OK

  39. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A0155I5E25
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-5 (CANH) - E69-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY) Click here

    OK

    REPLACE NO. 2 JUNCTION CONNECTOR

  40. CHECK FOR SHORT IN CAN BUS WIRES (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)


    1. A0155I5E24
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the F77 multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-2 (CANH) - E69-13 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

  41. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A0155I5E25
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the E35*1 or E81*2 air conditioning amplifier connector.


      • *1: w/ Rear Air Conditioning System

      • *2: w/o Rear Air Conditioning System

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E69-5 (CANH) - E69-16 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  42. CONNECT CONNECTOR


    1. Reconnect the E69 No. 2 junction connector.


    NEXT

  43. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A0155I5E19

      Disconnect the F73 No. 6 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      F73-7 (CANH) - F73-18 (CANL) Ignition switch off 108 to 132 Ω
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 6 Junction Connector)

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

  44. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)


    1. A0157YPE06
      Text in Illustration
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) Ignition switch off 108 to 132 Ω
      Result
      Result Proceed to
      OK (w/ TOYOTA parking assist-sensor system) A
      OK (w/o TOYOTA parking assist-sensor system) B
      NG C

    B

    REPLACE NO. 6 JUNCTION CONNECTOR

    C

    CONNECT CONNECTOR Click here

    A

  45. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)


    1. A0155I5E31
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 6 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      F73-5 (CANH) - F73-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY) Click here

    OK

    REPLACE NO. 6 JUNCTION CONNECTOR

  46. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)


    1. A0155I5E31
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 6 Junction Connector)

      Disconnect the F12 clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      F73-5 (CANH) - F73-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (CANH, CANL)

    OK

    REPLACE CLEARANCE WARNING ECU ASSEMBLY Click here

  47. CONNECT CONNECTOR


    1. Reconnect the F73 No. 6 junction connector.


    NEXT

  48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)


    1. A0155I5E32
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E75 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-1 (CANH) - E75-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

    OK

  49. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    1. A0155I5E28
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-4 (CANH) - E75-15 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) Click here

    OK

  50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SKID CONTROL ECU)


    1. A0155I5E33
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-5 (CANH) - E75-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU) Click here

    OK

  51. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A0155I5E29
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-3 (CANH) - E75-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY) Click here

    OK

    REPLACE NO. 3 JUNCTION CONNECTOR

  52. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    1. A0155I5E28
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E3 main body ECU (cowl side junction block LH) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-4 (CANH) - E75-15 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

  53. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)


    1. A0155I5E33
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-5 (CANH) - E75-16 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

    OK

    REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) Click here

  54. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    1. A0155I5E29
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the E7 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      E75-3 (CANH) - E75-14 (CANL) Ignition switch off 1 MΩ or higher
      Result
      Result Proceed to
      OK (w/ Multi-information Display) A
      OK (w/o Multi-information Display) B
      NG C

    B

    REPLACE COMBINATION METER ASSEMBLY Click here

    C

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

    A

    REPLACE COMBINATION METER ASSEMBLY Click here