CLEARANCE SONAR MAIN SWITCH REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE INSTRUMENT SIDE PANEL LH

    A0155UDE06
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  2. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A0156ALE04
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.

  3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

      A0159Y8E01
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
      *1 Protective Tape - -

  4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. A015D40

      Remove the clip.

    2. Remove the screw.

    3. Detach the 8 claws.

    4. Remove the panel pad and disconnect the connectors and 2 clamps.

  5. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

      A0159Y8E01
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
      *1 Protective Tape - -

  6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A0159IW

    1. Remove the 2 screws.

    2. Detach the 3 claws.

    3. Disconnect the connectors and remove the No. 1 instrument panel under cover.

  7. REMOVE NO. 1 LOWER INSTRUMENT PANEL FINISH PANEL

    A015CNPE02

    1. Using a screwdriver, detach the 2 claws and open the hole cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape

    2. w/ Driver Side Knee Airbag:


      1. Remove the 2 bolts.

      2. Detach the 16 claws.

        A015CUJ

    3. w/o Driver Side Knee Airbag:


      1. Remove the 2 bolts.

      2. Detach the 9 claws.

        A015A9A
    4. A0158MF

      for Automatic Air Conditioning System:


      1. Detach the 2 claws and remove the room temperature sensor.

    5. A0156SA

      Detach the 2 claws and disconnect the 2 control cables.

    6. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.

  8. REMOVE NO. 1 SWITCH HOLE BASE

    A015DE6

    1. Detach the 4 claws.

    2. Disconnect the connectors and remove the No. 1 switch hole cover.

  9. REMOVE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY


    1. A015ATGE01
      Text in Illustration
      *A for LHD
      *B for RHD

      Detach the 2 claws and remove the back sonar or clearance sonar switch assembly.