Click here

PARKING ASSIST MONITOR SYSTEM (w/ Side Monitor System) Image from Camera for Parking Assist Monitor is Abnormal

Click here
Click here Click here
DTC Code DTC Name
  Image from Camera for Parking Assist Monitor is Abnormal
Click here

DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the multi-display assembly via the parking assist ECU.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • When "System initializing" is displayed on the parking assist ECU after the battery terminal has been disconnected, correct the steering angle neutral point (Click here).

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/ Side Monitor System) may be needed (Click here).

Tip:

Images can be difficult to discern even in normal conditions. For example:


  • Noise may occur in the image during power back door operation (w/ Power Back Door System).

  • Noise may occur in the image depending on electrical devices used in the cabin.

  • Noise may occur in the image if accessories that generate radio waves have been installed.

  • The camera screen is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

  • The camera lens is dirty with snow, mud, etc.

  • A strong beam of light, such as a sunbeam or headlight, hits the camera.

  • It is too dark around the camera (at night etc.).

  • The ambient temperature around the camera is either too high or too low.

  • The vehicle is tilted at a steep angle.

  • The ambience of the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, particular to the CCD camera.)

Click here

PROCEDURE


  1. Click here

    CHECK SIDE MONITOR SYSTEM


    1. Check if the same malfunction occurs when the side monitor screen is displayed.

      Table 1. Result
      Result Proceed to
      Malfunction occurs when parking assist monitor screen is displayed (side monitor screen is normal). A
      Malfunction occurs when parking assist monitor screen and side monitor screen are displayed. B

  2. Click here

    CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY AND BODY GROUND)


    1. Disconnect the F75 and F76 parking assist ECU connectors.

    2. Disconnect the S5 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F76-38 (CV-) - S5-1 (CV-) Always Below 1 Ω
      F76-15 (CV+) - S5-2 (CV+) Always Below 1 Ω
      F76-14 (CB+) - S5-4 (CB+) Always Below 1 Ω
      F76-37 (CGND) - S5-3 (CGND) Always Below 1 Ω
      F75-4 (GND1) - Body ground Always Below 1 Ω
      F76-38 (CV-) - Body ground Always 10 kΩ or higher
      F76-15 (CV+) - Body ground Always 10 kΩ or higher
      F76-14 (CB+) - Body ground Always 10 kΩ or higher
      F76-37 (CGND) - Body ground Always 10 kΩ or higher

  3. Click here

    CHECK PARKING ASSIST ECU (CB+, CGND)


    1. A015AY7E20

      Reconnect the F75 and F76 parking assist ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F76-37 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F76-14 (CB+) - F76-37 (CGND) Engine switch on (IG), shift lever in R 5.5 to 7.05 V
      Table 2. Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

  4. Click here

    CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)


    1. A0155GTE19

      Reconnect the S5 rear television camera assembly connector.

      Table 3. Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      		 *b Waveform A
      *c Waveform B *d Synchronization Signal
      *e Video Waveform - -

    2. Check the waveform of the rear television camera assembly using an oscilloscope.

      Tip:

      • A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.

      • The video waveform changes according to the image sent by the rear television camera assembly.

      Item Content
      Terminal No. (Symbol) F76-15 (CV+) - F76-37 (CGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      • Waveform A: Engine switch on (IG), shift lever in R and camera lens is not covered, displaying an image

      • Waveform B: Engine switch on (IG), shift lever in R and camera lens is covered, blacking out the screen
      OK
      Waveform is as shown in the illustration.

  5. Click here

    CHECK HARNESS AND CONNECTOR (GVIF CABLE)


    1. Replace the GVIF cable with a normally functioning one.

    2. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).

  6. Click here

    CHECK MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly with a normally functioning one (Click here).

    2. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).

  7. Click here

    END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    REPLACE PARKING ASSIST ECUClick here

  10. Click here

    REPLACE REAR TELEVISION CAMERA ASSEMBLYClick here

  11. Click here

    END (GVIF CABLE IS DEFECTIVE)