SIDE MONITOR SYSTEM CALIBRATION


  1. ADJUST SIDE MONITOR SYSTEM


    1. This side monitor system can be set from the diagnostic screen of the multi-display assembly.

    2. If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.

      Part Name Operation Adjustment Item Proceed to
      Steering sensor

      • Removal and installation of the Steering angle sensor

      • Removal and installation of the connector of the Steering angle sensor

      • Replacement

      		 Steering angle neutral point

      Click here

      Steering angle setting

      Click here

      Multi-media module receiver assembly Replacement Vehicle contract setting

      Click here

      Parking assist ECU Replacement Parking assist ECU initialization

      Click here

      Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Rear television camera optical axis (Camera position setting)

      Click here

      Side television camera optical axis (Camera position setting) Procedure 1
      Side television camera assembly

      • Replacement

      • Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.

      		 Side television camera optical axis (Camera position setting) Procedure 1
      Outer rear view mirror assembly Replacement Side television camera optical axis (Camera position setting) Procedure 1

      Note

      After the engine switch is turned off, the multi-media module receiver assembly requires approximately 60 seconds to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      Tech Tips

      The adjustment values stored while performing side monitor system calibration are stored in the parking assist ECU.

  2. SIDE CAMERA SETTING (Procedure 1)

    Tech Tips

    Be sure to check for DTCs before performing this procedure Click here.


    1. Preparation for adjustment


      1. Park the vehicle with the steering wheel centered.

      2. A015D8LE03
        Text in Illustration
        *a Vehicle Center
        *b Target Bar for Back Camera Adjustment
        *c Vehicle End
        *d Front Side

        Set a target bar for optical axis adjustment of the rear television camera.

        Tech Tips

        Only when adjusting the optical axis of the camera, create a target bar for adjustment.

        Tech Tips


        • Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.79 to 1.18 in.) and 1995 to 2005 mm (6.55 to 6.58 ft.), respectively. Check the color on the multi-display assembly and choose a tape color which can be easily seen.

        • Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.

        • Check that the back door is fully closed.

      3. Set a target bar for optical axis adjustment of the side television camera.

        Tech Tips

        Only when adjusting the optical axis of the camera, create a target bar for adjustment.

        A0158L3E06
        4. Text in Illustration
        *A for LHD - -
        *a Target Bar for Side Camera Adjustment *b Front Wheel Axis
        *c Front Side *d Vehicle Center
        A015BZ8E04
        Text in Illustration
        *A for RHD - -
        *a Target Bar for Side Camera Adjustment *b Front Wheel Axis
        *c Front Side *d Vehicle Center

        Tech Tips

        Target bars for side camera adjustment should be made with 2 pieces of 2.5 cm wide tape; one piece should be 100 cm (3.28 ft.) (C+D) and the other should be 68 cm (2.23 ft.) (E+F) long. Check the tape color on the multi-media module receiver assembly and choose a tape color which can be easily seen.

      4. Start diagnostic mode Click here.

        Note

        Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.

        Tech Tips

        The displayed items may differ depending on vehicle specifications.


        1. A015APK

          Select "Function Check/Setting" on the [Service Menu] screen.

        2. A01584W

          Select "Camera Setting" on the [Function Check/Setting] screen.

        3. A0155MF

          Select "Side Camera Setting" on the [Mode Setting] screen.

          Tech Tips

          To select a grayed out item, select and hold the item for 2 seconds or more.

        4. A0155L5

          Select "Next" on the [Signal Check] screen.

          Note


          • When "CHK" (red) is displayed for any items on the [Signal Check] screen, selecting "Next" will not change the screen to the [Side Camera Position Setting] screen.

          • When "CHK" (red) is displayed for any items on the [Signal Check] screen, perform inspections using the [Signal Check] screen Click here.

          Tech Tips


          • When the outer mirrors are retracted, selecting "Next" will not change the screen to the [Side Camera Position Setting] screen.

          • If the screen does not change to the [Side Camera Position Setting] screen even though the outer mirrors are extended, perform the "MIRROR SW" check on the [Signal Check] screen Click here.

          • If the screen does not change to the [Side Camera Position Setting] screen even after "OK" (blue) is displayed as a result of the MIRROR SW check on the [Signal Check] screen, replace the parking assist ECU Click here.

      5. A015C1ZE02

        Side Camera Position Setting:

        Tech Tips

        Colors used on the [Side Camera Position Setting] screen

        6. Text in Illustration
        *a Target Adjustment Bar for Side Camera Position Setting
        *b Red Frame
        *c Yellow Frame

    1. A015DG4E02

      Perform the roll angle adjustment.


      • Select switches A and B to rotate C so that it is parallel to the target adjustment bar.

    2. Perform the vertical and horizontal position adjustment.


      • Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.

    3. Select "Next" to display [Side Verify Mode].

  3. Side Verify Mode:


    1. A015AKC

      Check that the red cross and the target adjustment bar are aligned.

      Tech Tips

      If they are not aligned, select "Back" and perform [Side Camera Position Setting] again.

    2. Select "Next" to display [Side Camera Signal Check].

  4. Side Camera Signal Check:


    1. A015D6LE01

      Select "OK" to store the side camera aiming adjustment value and change the screen to the [Service Menu] screen.

      Tech Tips


      • When "OK" is selected, a beep will sound to confirm that the side camera aiming adjustment values have been stored.

      • The adjustment value will not be stored unless "Back" is selected.

  5. Finish diagnostic mode Click here.