NAVIGATION SYSTEM, Diagnostic DTC:B15D5

DTC Code DTC Name
B15D5 Rear Seat Entertainment System Disconnected

DESCRIPTION

The multi-media module receiver assembly and television display assembly are connected by the MOST communication line.

When a MOST communication error occurs between the multi-media module receiver assembly and television display assembly, these DTCs will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D5 A device that is listed in the MOST network connected device record of the master unit is missing.

  • Television display assembly power source circuit

  • MOST circuit between stereo component amplifier assembly and television display assembly

  • MOST circuit between television display assembly and multi-media module receiver assembly

  • Television display assembly

  • Multi-media module receiver assembly

Tech Tips

For the MOST network, the multi-media module receiver assembly is the master unit.

WIRING DIAGRAM

A0157XME02

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components.


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B

        Tech Tips


        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.

        • This DTC may be stored when a MOST communication error occurs due to electrical noise.


    B

    CLEAR DTC Click here

    A

  2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.


    NEXT

  3. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  4. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTCs are output.

    NG

    CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND) Click here

    OK

    END (COMMUNICATION MALFUNCTION DUE TO NOISE)

  5. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)


    1. A01554GE05
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Television Display Assembly)

      Disconnect the television display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L53-3 (GND) - Body ground Always Below 1 Ω
      L53-4 (GND2) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L53-11 (+B2) - L53-3 (GND) Always 11 to 14 V
      L53-1 (+B) - L53-3 (GND) Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the L56 television display assembly connector.

    2. Disconnect the F85 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L56-2 (MI+) - F85-5 (MO+) Always Below 1 Ω
      L56-3 (MI-) - F85-6 (MO-) Always Below 1 Ω
      L56-4 (SLDI) - F85-7 (SLDO) Always Below 1 Ω
      L56-2 (MI+) - Body ground Always 10 kΩ or higher
      L56-3 (MI-) - Body ground Always 10 kΩ or higher
      L56-4 (SLDI) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)


    1. Disconnect the L56 television display assembly connector.

    2. Disconnect the F84 multi-media module receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L56-5 (MO+) - F84-2 (MI+) Always Below 1 Ω
      L56-6 (MO-) - F84-3 (MI-) Always Below 1 Ω
      L56-7 (SLDO) - F84-4 (SLDI) Always Below 1 Ω
      L56-5 (MO+) - Body ground Always 10 kΩ or higher
      L56-6 (MO-) - Body ground Always 10 kΩ or higher
      L56-7 (SLDO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. REPLACE TELEVISION DISPLAY ASSEMBLY


    1. Replace the television display assembly Click here.


    NEXT

  9. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  10. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTCs are output.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)