Click here

NAVIGATION SYSTEM, Diagnostic DTC:B15D0

Click here
Click here Click here
DTC Code DTC Name
B15D0 MOST Communication Malfunction
Click here

DESCRIPTION

This DTC is stored when the MOST network cannot be established after the master unit is activated.

Tip:

  • If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the navigation system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

  • When the stereo component amplifier assembly stops operating and a malfunction occurs in the navigation system due to a short in a speaker circuit, this DTC will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D0 MOST network cannot be established.

  • MOST line check

  • MOST communication line connector

  • MOST communication line

  • Television display assembly (w/ Rear Seat Entertainment System)

  • Stereo component amplifier assembly

  • Multi-media module receiver assembly
Tip:

  • For the MOST network, the multi-media module receiver assembly is the master unit.

  • Errors may occur in MOST communication between devices due to problems such as electrical noise.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Table 1. Result
      Result Proceed to
      Optional components (including associated wiring) are installed. A

      Optional components (including associated wiring) are installed.

      DTCs are not output.

      		 B
      Tip:

      • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

      • These DTCs may be stored when an AVC-LAN communication error occurs due to electrical noise.


  2. Click here

    CONFIRM SYMPTOMS


    1. Turn the engine switch off.

    2. Turn the engine switch on (ACC) and check if the audio system activates and if the speakers operate.

      Tip:

      • Choose a source such as radio so that sound can be output from the speakers.

      • If sound from the speakers is low, turn up the volume.

      Table 2. Result
      Result Proceed to
      Even after the engine switch is turned on (ACC), the navigation system does not activate and sound is not output from the speakers. (w/o Rear Seat Entertainment System) A
      Even after the engine switch is turned on (ACC), the navigation system does not activate and sound is not output from the speakers. (w/ Rear Seat Entertainment System) B
      The audio system activates when the engine switch is turned on (ACC) but the sound stops being output when the amplifier output exceeds a certain level. C
      Tip:

      • If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the navigation system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

      • When the stereo component amplifier assembly stops operating and a malfunction occurs in the navigation system due to a short in a speaker circuit, this DTC will be stored. In this case, check each speaker circuit and repair or replace malfunctioning parts, and then recheck for DTCs.


  3. Click here

    CHECK MOST COMMUNICATION CONNECTORS


    1. A0159EPE01

      Display the "MOST Line Check" screen (Click here).

    2. Check the result on the "MOST Line Check" screen.

      Table 3. Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      "OK" is displayed for all items. B

      • When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

      • The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.

      Table 4. Text in Illustration
      *a Node position number for devices that use MOST communication
      *b Device name
      *c Result

  4. Click here

    CONFIRM SYMPTOMS


    1. Check the MOST communication line connectors.


      1. Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (Click here).

    2. Display the "MOST Line Check" screen and check the result (Click here).

      Table 5. Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      The screen cannot be changed to the "MOST Line Check" screen. B
      Tip:

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


  5. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)


    1. A01591NE10

      Disconnect the stereo component amplifier assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F85-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher
      Table 6. Text in Illustration
      *a

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

  6. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F84 multi-media module receiver assembly connector.

    2. Disconnect the F85 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F84-1 (WUO) - F85-8 (WUI) Always Below 1 Ω
      F84-1 (WUO) - Body ground Always 10 kΩ or higher

  7. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F84 multi-media module receiver assembly connector.

    2. Disconnect the F85 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F85-2 (MI+) - F84-5 (MO+) Always Below 1 Ω
      F85-3 (MI-) - F84-6 (MO-) Always Below 1 Ω
      F85-4 (SLDI) - F84-7 (SLDO) Always Below 1 Ω
      F85-5 (MO+) - F84-2 (MI+) Always Below 1 Ω
      F85-6 (MO-)- F84-3 (MI-) Always Below 1 Ω
      F85-7 (SLDO) - F84-4 (SLDI) Always Below 1 Ω
      F85-2 (MI+) - Body ground Always 10 kΩ or higher
      F85-3 (MI-) - Body ground Always 10 kΩ or higher
      F85-4 (SLDI) - Body ground Always 10 kΩ or higher
      F85-5 (MO+) - Body ground Always 10 kΩ or higher
      F85-6 (MO-) - Body ground Always 10 kΩ or higher
      F85-7 (SLDO) - Body ground Always 10 kΩ or higher

  8. Click here

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY


    1. Replace the stereo component amplifier assembly with a new or normally functioning one (Click here).


  9. Click here

    CLEAR DTC


    1. Clear the DTCs (Click here).


  10. Click here

    CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again (Click here).

      OK
      No DTCs are output

  11. Click here

    MOST COMMUNICATION CONNECTORS


    1. A0157A5E01

      Display the "MOST Line Check" screen (Click here).

    2. Check the result on the "MOST Line Check" screen.

      Table 7. Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      "NCON" is displayed for "RSE". B
      "OK" is displayed for all items. C

      • When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

      • The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.

      Table 8. Text in Illustration
      *a Node position number for devices that use MOST communication
      *b Device name
      *c Result

  12. Click here

    CONFIRM SYMPTOMS


    1. Check the MOST communication line connectors.


      1. Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (Click here).

    2. Display the "MOST Line Check" screen and check the result (Click here).

      Table 9. Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      The screen cannot be changed to the "MOST Line Check" screen. B
      Tip:

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


  13. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)


    1. A01591NE10

      Disconnect the stereo component amplifier assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F85-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher
      Table 10. Text in Illustration
      *a

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

  14. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F84 multi-media module receiver assembly connector.

    2. Disconnect the F85 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F84-1 (WUO) - F85-8 (WUI) Always Below 1 Ω
      F84-1 (WUO) - Body ground Always 10 kΩ or higher

  15. Click here

    CONFIRM SYMPTOMS


    1. Check the MOST communication line connectors.


      1. Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (Click here).

    2. Display the "MOST Line Check" screen and check the result (Click here).

      Table 11. Result
      Result Proceed to
      "NCON" is displayed for "RSE". A
      The screen cannot be changed to the "MOST Line Check" screen. B
      Tip:

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


  16. Click here

    CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY Wake Up LINE)


    1. A01591NE11

      Disconnect the television display assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L56-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher
      Table 12. Text in Illustration
      *a

      Front view of wire harness connector

      (to Television Display Assembly)

  17. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)


    1. Disconnect the F85 stereo component amplifier assembly connector.

    2. Disconnect the L56 television display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F85-1 (WUO) - L56-8 (WUI) Always Below 1 Ω
      F85-1 (WUO) - Body ground Always 10 kΩ or higher

  18. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F84 multi-media module receiver assembly connector.

    2. Disconnect the F85 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F85-2 (MI+) - F84-5 (MO+) Always Below 1 Ω
      F85-3 (MI-) - F84-6 (MO-) Always Below 1 Ω
      F85-4 (SLDI) - F84-7 (SLDO) Always Below 1 Ω
      F85-2 (MI+) - Body ground Always 10 kΩ or higher
      F85-3 (MI-) - Body ground Always 10 kΩ or higher
      F85-4 (SLDI) - Body ground Always 10 kΩ or higher

  19. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)


    1. Disconnect the F85 stereo component amplifier assembly connector.

    2. Disconnect the L56 television display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F85-5 (MO+) - L56-2 (MI+) Always Below 1 Ω
      F85-6 (MO-) - L56-3 (MI-) Always Below 1 Ω
      F85-7 (SLDO) - L56-4 (SLDI) Always Below 1 Ω
      F85-5 (MO+) - Body ground Always 10 kΩ or higher
      F85-6 (MO-) - Body ground Always 10 kΩ or higher
      F85-7 (SLDO) - Body ground Always 10 kΩ or higher

  20. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)


    1. Disconnect the F84 multi-media module receiver assembly connector.

    2. Disconnect the L56 television display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F84-2 (MI+) - L56-5 (MO+) Always Below 1 Ω
      F84-3 (MI-) - L56-6 (MO-) Always Below 1 Ω
      F84-4 (SLDI) - L56-7 (SLDO) Always Below 1 Ω
      F84-2 (MI+) - Body ground Always 10 kΩ or higher
      F84-3 (MI-) - Body ground Always 10 kΩ or higher
      F84-4 (SLDI) - Body ground Always 10 kΩ or higher

  21. Click here

    REPLACE TELEVISION DISPLAY ASSEMBLY


    1. Replace the television display assembly with a new or normally functioning one (Click here).


  22. Click here

    CLEAR DTC


    1. Clear the DTCs (Click here).


  23. Click here

    CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again (Click here).

      OK
      No DTCs are output.

  24. Click here

    GO TO AUDIO AND VISUAL SYSTEMClick here

  25. Click here

    USE SIMULATION METHOD TO CHECKClick here

  26. Click here

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLYClick here

  27. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  28. Click here

    END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

  29. Click here

    USE SIMULATION METHOD TO CHECKClick here

  30. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  31. Click here

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLYClick here

  32. Click here

    USE SIMULATION METHOD TO CHECKClick here

  33. Click here

    REPLACE TELEVISION DISPLAY ASSEMBLYClick here

  34. Click here

    END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)