RADIO RECEIVER (w/ Multi-display) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

    A015940E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    2. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.

  4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

    A015BUX

    1. Remove the clip and screw.

    2. Detach the 8 claws.

    3. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.

  5. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

    A015CGBE02
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the No. 1 instrument panel finish panel cushion.

    2. Using a moulding remover, detach the 7 claws and remove the No. 1 instrument panel finish panel cushion.

  6. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH

    A015BRH

    1. Remove the clip and screw.

    2. Detach the 7 claws and remove the lower instrument panel pad sub-assembly.

  7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

    A015A00

    1. Detach the 7 claws.

    2. Disconnect the connectors and remove the lower center instrument cluster finish panel sub-assembly.

  8. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

    A015A0J

    1. Detach the 8 claws and remove the opening cover.

  9. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

    A0157IUE02
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the No. 3 instrument panel register.

  10. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

    A015DBME02
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the No. 4 instrument panel register.

  11. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET


    1. A015CPE

      Remove the 2 screws and 2 bolts.

    2. A0155D4

      Pull the multi-display assembly to detach the 2 clips and 6 claws on the backside of the multi-display assembly.

    3. Disconnect the connectors and remove the multi-display assembly.

  12. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET


    1. A015D93

      Remove the 2 screws and 2 bolts.

    2. A015A31

      Pull the multi-media module receiver assembly to detach the 5 claws on the backside of the multi-media module receiver assembly.

    3. Disconnect the connectors and remove the multi-media module receiver assembly.

  13. REMOVE NO. 1 RADIO BRACKET


    1. A015ASU

      Remove the 3 bolts and No. 1 radio bracket.

  14. REMOVE NO. 2 RADIO BRACKET


    1. A015CQM

      Remove the 3 bolts and No. 2 radio bracket.