Click here

STEERING CONTROL ECU (for LHD) INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL STEERING CONTROL ECU


    1. Install the steering control ECU to the junction block with the bolt and nut.

      8.0 N*m 82 kgf*cm 71 in.*lbf
  2. Click here

    INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK


    1. Front side:


      1. Connect the 5 connectors.

    2. Rear side:


      1. Install the steering control ECU with junction block with the bolt and 2 nuts.

        8.0 N*m 82 kgf*cm 71 in.*lbf

      2. Attach the 2 clamps.

      3. Connect the 7 connectors.

  3. Click here

    INSTALL LOWER INSTRUMENT PANEL (w/o Driver Side Knee Airbag)


    1. Attach the 2 claws and connect the DLC3.

    2. Install the lower instrument panel with the 5 bolts.

  4. Click here

    INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


    1. A01556EE01

      Connect the connector.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  5. Click here

    INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect the connectors.

    2. Attach the 4 claws to install the No. 1 switch hole base.

  6. Click here

    INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connectors.

    2. A0158MF

      for Automatic Air Conditioning System:


      1. Attach the 2 claws to install the room temperature sensor.

    3. A0156SA

      Attach the 2 claws to connect the 2 control cables.

    4. w/ Driver Side Knee Airbag:


      1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

      2. A015CUJ

        Install the 2 bolts.

    5. w/o Driver Side Knee Airbag:


      1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

      2. A015A9A

        Install the 2 bolts.

    6. A015ATT

      Attach the 2 claws to close the hole cover.

  7. Click here

    INSTALL COWL SIDE TRIM BOARD LH


    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  8. Click here

    INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


    1. Connect the connectors.

    2. Attach the 3 claws to install the No. 1 instrument panel under cover.

    3. Install the 2 screws.

  9. Click here

    INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 7 claws and 4 clips to install the scuff plate.

  10. Click here

    INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A0156L8E01

      Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

      Table 1. Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
  11. Click here

    INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.

  12. Click here

    INSTALL INSTRUMENT SIDE PANEL LH


    1. Attach the 6 claws to install the instrument side panel.

  13. Click here

    INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Connect the connectors.

    2. Attach the 7 claws to install the lower center instrument cluster finish panel sub-assembly.

  14. Click here

    INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH


    1. Attach the 7 claws to install the lower instrument panel pad sub-assembly.

    2. Install the clip and screw.

  15. Click here

    INSTALL NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. Attach the 7 claws to install the No. 1 instrument panel finish panel cushion.

  16. Click here

    INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. Connect the connectors and attach the 2 clamps.

    2. Attach the 8 claws to install the lower instrument panel pad sub-assembly.

    3. Install the clip and screw.

  17. Click here

    INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. Attach the 7 claws to install the No. 2 instrument panel finish panel cushion.

  18. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).