Click here

PARKING BRAKE CABLE INSTALLATION

Click here
Click here Click here
Tip:

  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.

Click here
  1. Click here

    INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 2 parking brake cable clamp.

    2. A0159Z2E01

      Install the No. 2 parking brake cable with the 6 bolts.

      13 N*m 127 kgf*cm 9 ft.*lbf

    3. Install the fuel tank (Click here).

    4. A0155TM

      Attach the claws of the No. 2 parking brake cable.

    5. A015BQ0

      Connect the No. 2 parking brake cable to the No. 1 parking brake pull rod.

  2. Click here

    INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 3 parking brake cable clamp.

    2. A015A4FE01

      Install the No. 3 parking brake cable with the 6 bolts.

      13 N*m 127 kgf*cm 9 ft.*lbf
    3. A015AV4

      Attach the claws of the No. 3 parking brake cable.

    4. A015BQ0

      Connect the No. 3 parking brake cable to the No. 1 parking brake pull rod.

  3. Click here

    CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A015636

      Connect the No. 3 parking brake cable with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf
  4. Click here

    INSTALL PARKING BRAKE SHOE LEVER LH


    1. A01577ZE01

      Apply high temperature grease to the parking brake anchor block.

    2. Install the parking brake shoe lever to the No. 3 parking brake cable.

      Note:

      Be carefully to distinguish between the parking brake shoe lever RH and LH.

  5. Click here

    INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH


    1. Apply high temperature grease to the areas of the backing plate that contact the shoe.

    2. A01570ME01

      Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.

      09718-00011
  6. Click here

    INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH


    1. Apply high temperature grease to the areas of the backing plate that contact the shoe.

    2. A015BATE01

      Apply high temperature grease to the thread and all joining areas of the parking brake shoe adjuster screw set.

    3. A015E3N

      Set the No. 1 parking brake shoe and shoe adjuster screw set in place.

    4. A01579B

      Connect the tension spring.

    5. A0156PXE01

      Using SST, install the shoe hold down spring pin, compression spring and shoe hold down spring cup.

      09718-00011
  7. Click here

    INSTALL PARKING BRAKE SHOE RETURN SPRING


    1. A015B5EE01

      Using SST, install the shoe return spring.

      09703-30011
  8. Click here

    CHECK PARKING BRAKE INSTALLATION


    1. A0155E6E01

      Check that each part is installed properly.

  9. Click here

    INSTALL REAR DISC


    1. A015ALXE01

      Align the matchmarks, and then install the rear disc.

      Tip:

      When replacing the rear disc with a new one, select the installation position where the rear disc has the minimum runout.

  10. Click here

    CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH


    1. A015DKT

      Connect the rear disc brake cylinder with 2 new bolts.

      95 N*m 969 kgf*cm 70 ft.*lbf
      Note:

      • Do not twist the brake hose.

      • Make sure that the bolts are free from damage and foreign matter.

      • Do not overtighten the bolts.

  11. Click here

    INSTALL REAR NO. 2 SUSPENSION CONTROL ACCUMULATOR BRACKET


    1. Install the bracket to the shock absorber control valve with the bolt.

      18 N*m 184 kgf*cm 13 ft.*lbf
  12. Click here

    INSTALL HEIGHT CONTROL UNIT PROTECTOR PIPE


    1. A015BRP

      Install the protector pipe with the 6 bolts.

      16 N*m 163 kgf*cm 12 ft.*lbf
  13. Click here

    ADJUST PARKING BRAKE

    (Click here)

  14. Click here

    INSTALL REAR WHEEL

    for Aluminum Wheel
    131 N*m 1336 kgf*cm 97 ft.*lbf
    for Steel Wheel
    209 N*m 2131 kgf*cm 154 ft.*lbf
  15. Click here

    INSTALL LOWER CONSOLE BOX (w/o Console Box Lid)

    (Click here)

  16. Click here

    INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)

    (Click here)

  17. Click here

    INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

    (Click here)