VEHICLE STABILITY CONTROL SYSTEM Crawl Indicator Light Remains ON

DESCRIPTION

When CRAWL starts after operating the CRAWL switch, the CRAWL indicator light turns on. While CRAWL is in the process of stopping, the CRAWL indicator light begins blinking. When CRAWL totally stops, the CRAWL indicator light turns off.

INSPECTION PROCEDURE

PROCEDURE

1. Click here

   CHECK CAN COMMUNICATION LINE

   
   

   1. Turn the ignition switch off.

   2. Connect the GTS to the DLC3.

   3. Turn the ignition switch to ON and the GTS on.

   4. Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

      OK
      "CAN Bus Check" indicates no malfunctions in CAN communication.

      Table 1. Result

      Result	Proceed to
      OK	A
      NG (for LHD)	B
      NG (for RHD)	C

   
   
   • AClick here
   • BClick here
   • CClick here
2. Click here

   CHECK DTC (CAN COMMUNICATION SYSTEM)

   
   

   1. Turn the ignition switch off.

   2. Connect the GTS to the DLC3.

   3. Turn the ignition switch to ON and the GTS on.

   4. Check for DTCs (for LHD:Click here, for RHD:Click here).

      Table 2. Result

      Result	Proceed to
      CAN system DTC is not output	A
      CAN system DTC is output (for LHD)	B
      CAN system DTC is output (for RHD)	C

   
   
   • AClick here
   • BClick here
   • CClick here
3. Click here

   PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)

   
   

   1. Turn the ignition switch off.

   2. Connect the GTS to the DLC3.

   3. Turn the ignition switch to ON.

   4. Turn the GTS on.

   5. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

      Table 3. ABS/VSC/TRC

      Tester Display	Test Part	Control Range	Diagnostic Note
      Crawl Control Light	CRAWL indicator light	Indicator light ON/OFF	Observe the combination meter.

   6. When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List.

      Table 4. ABS/VSC/TRC

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Crawl Control Light	CRAWL indicator light/ ON or OFF	ON: Indicator light on OFF: Indicator light off	-

      Table 5. Result

      Result		Proceed to
      Data List Display	Data List Display when Performing Active Test ON/OFF Operation
      ON	Changes between ON and OFF	A
      	Does not change between ON and OFF (for LHD)	B
      	Does not change between ON and OFF (for RHD)	C
      OFF	Changes between ON and OFF	A
      	Does not change between ON and OFF (for LHD)	B
      	Does not change between ON and OFF (for RHD)	C

   
   
   • AClick here
   • BClick here
   • CClick here
4. Click here

   GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

5. Click here

   GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

6. Click here

   GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

7. Click here

   REPLACE MASTER CYLINDER SOLENOIDClick here

8. Click here

   GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

9. Click here

   GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

10. Click here

    REPLACE MASTER CYLINDER SOLENOIDClick here