Click here

VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1437

Click here
Click here Click here
DTC Code DTC Name
C1437 Lost Communication with ECM
Click here

DESCRIPTION

The skid control ECU (master cylinder solenoid) receives signals from the ECM via the CAN communication system.

DTC Code DTC Detection Condition Trouble Area
C1437 When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent from the ECM for 2 seconds or more.

  • Engine control system

  • CAN communication system

  • Skid control ECU (Master cylinder solenoid)
Click here

INSPECTION PROCEDURE

Note:

When replacing the master cylinder solenoid, perform calibration (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)


    1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

      Table 1. ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      EFI Communication Open EFI communication open circuit detection/ Error or Normal Normal -
      OK
      Normal (there are no momentary interruptions).
      Tip:

      Perform the above inspection before removing the sensor and connector.


  2. Click here

    RECONFIRM DTC


    1. Clear the DTC (Click here).

    2. Turn the ignition switch off.

    3. Start the engine.

    4. Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

    5. Check that no CAN communication system DTC is output (Click here).

    6. Check if the same DTC is output (Click here).

      Table 2. Result
      Result Proceed to
      DTC C1437 is not output A
      DTC C1437 is output B
      CAN communication system DTC is output C
      Tip:

      Refer to the Engine Control System (How to Proceed with Troubleshooting) procedures:


      Tip:

      Refer to the CAN Communication System (How to Proceed with Troubleshooting) procedures:



  3. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - ECM)


    1. Turn the ignition switch off.

    2. Repair or replace the harness or connector.

    3. Check for any momentary interruption between the skid control ECU (master cylinder solenoid) and ECM (Click here).

    4. Check that there is no momentary interruption.


  4. Click here

    RECONFIRM DTC


    1. Clear the DTCs (Click here).

    2. Turn the ignition switch off.

    3. Start the engine.

    4. Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

    5. Check that no CAN communication system DTC is output (Click here).

    6. Check if the same DTC is output (Click here).

      Table 3. Result
      Result Proceed to
      DTC C1437 is not output A
      DTC C1437 is output (for LHD) B
      DTC C1437 is output (for RHD) C
      CAN communication system DTC is output (for LHD) D
      CAN communication system DTC is output (for RHD) E

  5. Click here

    CHECK FOR INTERMITTENT PROBLEMSClick here

  6. Click here

    END

  7. Click here

    REPLACE MASTER CYLINDER SOLENOIDClick here

  8. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

  9. Click here

    GO TO ENGINE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

  10. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

  11. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

  12. Click here

    REPLACE MASTER CYLINDER SOLENOIDClick here